User manual ICOM IC-F1610

[. . . ] AVOID placing the transceiver is excessively dusty environments. AVOID placing the transceiver against walls. This will obstruct heat dissipation. AVOID the use of chemical agents such as benzine or alcohol when cleaning, as they can damage the transceiver's surfaces. BE CAREFUL!The transceiver will become hot when operating continuously for long periods. iii TABLE OF CONTENTS IMPORTANT . 17 iv SUPPLIED ACCESSORIES q w e r LCD-STICKER t y u i o !0 !1 !2 !3 q Microphone (HM-100) . [. . . ] · The emergency call is transmitted one time only or repeatedly until receiving a control code, depending on the pre-settting. 1 D Programmable functions without supplied stickers TX CODE CHANNEL UP/DOWN KEY Push to select a TX code channel directly. CHANNEL UP/DOWN FUNCTION When a key is assigned this function, push it to increment or decrement the operating channel. CHANNEL SELECT FUNCTION When a key is assigned this function, push it to increment or decrement the operating channel. BANK UP/DOWN FUNCTION When a key is assigned this function, push it to increment or decrement the selected channel bank. PRIORITY CHANNEL A REWRITE FUNCTION When a key is assigned this function: Push momentarily to select PRIO A channel. DTMF RE-DIAL FUNCTION When a key is assigned this function, push it to automatically re-dial the most recent (manually transmitted) DTMF code. TX CODE KEY Selects a transmit 5-tone code (station code) chanCODE nel. · Push and hold to change the contents of the station code using the [CH UP]/[CH DN] keys. · Push to select a TX 5-tone code channel using the [CH UP]/[CH DN] keys after pushing this key. ID MEMORY READ KEY ID MR Recalls detected ID codes. · Push this key, then push [CH UP]/[CH DN] for selection. · Up to 5 ID's are remembered. Push and hold this key to erase all memorized ID's. OPT OPTION KEY TRUNKING GROUP KEY Push to select a trunking group (when operating in GRP SmarTrunk IITM mode). 5 1 PANEL DESCRIPTION TX CODE CHANNEL UP/DOWN FUNCTION When a key is assigned this function, push it to increment or decrement the TX code channel. TURBO SpeeDial A/B/C/D FUNCTIONS During SmarTrunk IITM operation, when a key is assigned this function, push it to automatically dial a commonly used number with one push. q w e r t y LOW CH09 173. 9 W LOW i output. u ACTIVATED KEY INDICATOR Appears or flashes to indicate the key directly below it has been activated. · Penalty timer Once the time-out timer is activated, transmission is further inhibited for a period determined by the penalty timer. I Receiving and transmitting RECEIVING: Push [ ] to turn power ON. When receiving a call, adjust the volume to comfortable listening level. TRANSMITTING: Lift the microphone off the microphone hanger. · 5-tone mute may be released (the `audible' condition is selected and "[ ]" appears. · A priority channel may be selected automatically. Wait for the channel to become clear. · The channel is busy when "[ ]" appears. Push the [CALL] key when initiating a call from your side. · Coded audio may be heard from the transceiver, then "[ ]" appears. · This step may not be necessary depending on your signalling system. Ask your system operator or dealer. While pushing and holding [PTT], speak into the microphone at your normal voice level. Release [PTT] to receive. IMPORTANT: To maximize the readability of your signal: · Pause briefly after pushing [PTT]. · Hold the microphone 15 to 20 cm from your mouth, then speak into the microphone at a normal voice level. 8 OPERATION D Tx code channel selection If the transceiver has the [TX CH] key, display can be toggled with the operating channel number (or name) and Tx code channel number (or name). [. . . ] You do not have to answer a group call to hear it over the air. 14 OPTIONAL SmarTrunk IITM OPERATION D Terminating a call After completing a call, push [#] to disconnect (hang up). IMPORTANT: If one person in the conversation terminates a call, all participants will be cut off. 4 D Programming memory speed dial Push and hold [M] until you hear a high-pitched beep. Enter the memory location (0­9, A, B, C, D), the telephone or subscriber number, then [1], [M] (or [3], [M] if for another system subscriber). · A high-pitched beep indicates successful programming. · Memories [A]­[D] are used for Turbo SpeeDial. D Last number redial Push [M], [M] to automatically redial the last number called. · A high-pitched beep indicates that the number is accepted. D System busy indication If all calls are busy, three low beeps sound after you initiate a call. [. . . ]