User manual ICOM IC-706MK2G

[. . . ] INSTRUCTION MANUAL i706MKTMG HF/VHF/UHF ALL MODE TRANSCEIVER This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT Read this instruction manual carefully before attempting to operate the transceiver. S a v e t h i s i n s t r u c t i o n m a n u a l . This instruction manual contains important safety and operating instructions for the IC-706MKIIG. PRECAUTIONS W RW A R N I N G H I G H V O L T A G E !N E V E R attach an antenna or internal antenna connector during transmission. [. . . ] This function removes the "push and hold [TUNER]" operation and activates first transmission on the new frequency. 54). 28 4 RECEIVE AND TRANSMIT I Split frequency operation Split frequency operation allows you to transmit and receive on two different frequencies. Split frequency operation uses 2 frequencies, one in VFO A and the other in VFO B. Following is an example of setting 7. 057 MHz, CW mode in VFO A (for receive) and 7. 025 MHz, CW mode in VFO B (for transmit). CW SPL VFO B ·The transmit frequency can be monitored while pushing [(F-3)XFC]. ·Split operation is now set for receive on 7. 057 MHz/CW and transmit on 7. 025 MHz/CW. Select VFO A and set the frequency to 7. 057 MHz/CW. ·[(F-2)A/B] is available when M1 appears. ·[(F-3)V/M] is available when M2 appears. CW To exchange the transmit and receive frequencies, push [(F-2)A/B] in M1. CONVENIENT VFO A Push or push and hold [(F-1)SPL] in the M1 display. Push and hold [SPL]: activates the quick split below. CW SPL The G3 display conveniently shows the transmit frequency during split frequency operation and [(F-3)Ñ] allows you to change the transmit frequency. · Split lock function The split lock function is convenient for changing only the transmit frequency. Otherwise, accidentally releasing the [(F-3)XFC] switch while rotating the main dial changes the receive frequency. The split lock's effectiveness can be selected in initial set mode (item 12) for both receive and transmit frequencies; or only the receive frequency. 52) VFO A To change the receive frequency, rotate the main dial; to change the transmit frequency, rotate the main dial while pushing [(F-3)XFC]. D Quick split function In M1, when you push [(F-1)SPL] for 2 sec. , split frequency operation is turned ON and VFO B is automatically changed according to the plus/minus preprogrammed shift frequency set in initial set mode (or equalized when 0 kHz is programmed as the split shift frequency). This shortens the time needed to start split frequency operation--great for DX'ing. has the same effect as pushing [(F-1)SPL] momentarily as in normal split operation. SPL Push VFO A SPL SPL PROGRAMMING SPLIT SHIFT FREQUENCY Push [POWER] to turn power OFF. While pushing [LOCK], push [POWER] to turn Select "SPL OFFSET" using [MENU], [M-CH] or the [Y]/[Z] keys, then rotate the main dial to select the desired split offset. ·The split offset can be selected from ­4000 kHz to +4000 kHz. F-1 for 2 sec. power ON and enter initial set mode. VFO A No shift frequency is programmed. SPL VFO B 16 SPL OFFSET SPL VFO A VFO B +10 kHz is programmed as a shift frequency. N o t e : This setting is not valid for FM operation. This is because FM operation uses the duplex setting for repeater operation (next page). 29 RECEIVE AND TRANSMIT 4 D Repeater operation A repeater amplifies received signals and retransmits them at a different frequency. When using a repeater, the transmit frequency is shifted from the receive frequency by an offset frequency. A repeater can be accessed using split frequency operation with the shift frequency set to the repeater's offset frequency. q Set the offset frequency and turn ON the quick split function in initial set mode in advance (p. 52). ·If the quick split function is turned OFF, both transmit and receive must be set separately. (Initial set mode default is ON. ) w Push [MODE] one or more times to select FM mode, then set the receive frequency. Push [DISPLAY] for 2 sec. , then push [MENU] one or more times to select "Q6 RPTR TONE. " · If FM mode has not been selected, this item does not appear. 12 QUICK SPLIT Set the tone frequency (quick set mode). 49 for setting details and available frequencies. Rotate the main dial to set a subaudible tone frequency. [. . . ] RTTY mode RF POWER RTTY TONE RTTY SHIFT RTTY KEYING Quick set mode Y No. Q1 Q2 Q3 Q4 Q5 MENU SSB/AM/FM mode RF POWER MIC GAIN VOX DELAY VOX GAIN ANTI VOX CARRIER Freq*1 RPTR TONE*2 TONE SQL*2 RPTR-T*3 T-SQL*4 2 CW mode RF POWER CW PITCH BK-IN DELAY CW PADDLE KEY SPEED RATIO M-CH Q6 Q7 Q8 1 Y 3 * SSB mode only; * FM mode only; * FM mode only/tone encoder ON; *4FM mode only/tone squelch ON. 68 Count on us! A-5564H-1EX-r Printed in Japan © 2001 by Icom Inc. 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003, Japan ABOUT CE DECLARATION OF CONFORMITY We Icom Inc. Japan 1-1-32 Kamiminami, Hirano-ku, Osaka 547-0003 Japan Declare on our sole responsibility that this equipment complies with the essential requirements of the Radio and Telecommunications Terminal Equipment Directive, 1999/5/CE, and that any applicable Essential Test Suite measurements have been performed. Kind of equipment: Type-designation: HF/VHF/UHF ALL MODE TRANSCEIVER Düsseldorf 13th Mar. [. . . ]