User manual ICOM IC-2KL

[. . . ] WORD D FEATURES V/V, U/U simultaneous receive capability Independent controls for each left and right bands Separate controller for flexible installation 50 W* of high transmit output power *VHF band; 35 W for UHF Remote control microphone standard New DMS (Dynamic Memory Scan) system i Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. PRECAUTION RWARNING RF EXPOSURE!If you have any questions regarding RF exposure and safety standards please refer to the Federal Communications Commission Office of Engineering and Technology's report on Evaluating Compliance with FCC Guidelines for Human Radio frequency Electromagnetic Fields (OET Bulletin 65). NEVER let objects impede the operation of the cooling fan on the rear panel. DO NOT push the PTT when not actually desiring to transmit. DO NOT allow children to play with any radio equipment containing a transmitter. [. . . ] To store the tone frequency permanently, overwrite the channel information. 25 v Push [Y] or [Z] to select and set the desired subaudible tone frequency. · Push and hold [Y]/[Z] to change the above tones continuously. b Push [CLR A(MW)] to exit set mode. · Subaudible tone frequency list 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 94. 8 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 159. 8 162. 2 165. 5 167. 9 171. 3 173. 8 177. 3 179. 9 183. 5 186. 2 189. 9 192. 8 196. 6 199. 5 (unit: Hz) 203. 5 206. 5 210. 7 218. 1 225. 7 229. 1 233. 6 241. 8 250. 3 254. 1 REPEATER OPERATION D DTMF tones DTMF-S 4 D 1750 Hz tone The microphone has 1750 Hz tone capability, used for ring tone when calling, etc. z Push [FUNC]. TONE-1 · The function indicator lights orange. Push [DTMF-S], then push the keys of the desired DTMF digits. · The function indicator lights green. · When "d" is displayed in place of the 100 MHz digit, cancel the DTMF memory encoder in advance. 49) · Push [DTMF-S] again to return the keypad to normal function control. Push , 4 M x Push [M(TONE-1)] to transmit a 1750 Hz tone call signal for 0. 5 sec. ; push and hold TONE-2 [0(TONE-2)] to transmit a 1750 Hz tone call signal for an arbitrary period. · The function indicator goes out automatically. 47 for details. 26 4 REPEATER OPERATION I Offset frequency USING SET MODE SET B When communicating through a repeater, the transmit frequency is shifted from the receive frequency by an amount determined by the offset frequency. Independent offset frequencies can be set for each operating frequency. qPush [MAIN·BAND] to select the desired band (left or right) as the main band. · Push [MAIN·BAND] for 1 sec. then rotate the [DIAL] to select the desired frequency band if necessary. z Push [BAND] to select the desired band (left or right) as the main band. · Enter the desired frequency via the keypad if necessary. x Select the desired mode/channel you wish to set the offset frequency to, such as VFO mode or memory/call channel. · The offset frequency can be independently programmed into each mode or channel. wSelect the desired mode/channel you wish to set the offset frequency to, such as VFO mode or memory/call channel. · The offset frequency can be independently programmed into each mode or channel. c Push [SET B(D-OFF)] to enter set mode. · Direct numeral input cannot be used. 5 [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 (blank channel) via the microphone. Push MAIN TX , MAIN TX Push then MAIN TX "Beep M M M Push MAIN TX Push then MAIN TX for 1 sec. and continue to push MAIN TX M M " "Beep " Beep " Beep " "Beep M 30 5 MEMORY OPERATION I Transferring memory contents This function transfers a memory channel's contents to VFO (or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency etc. D Memory/callVFO q Select the desired band's (left or right) memory or call channel. Push the desired band's [M/CALL·MW] several times to select memory mode or call channel, then rotate the same band's [DIAL] to select the desired memory or call channel. to transfer the selected memory/call channel contents to the VFO. · VFO mode is selected automatically. MR/CALL MW [Y]/[Z] z Push [BAND] to select the desired band as the main band, if necessary. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. to transfer the selected memory/call channel contents to the VFO. · VFO mode is selected automatically. [EXAMPLE]: Transferring memory channel 30 contents to VFO. Front panel operation: Push M/CALL to select memory mode. Rotate MW MAIN TX for selecting memory channel. MAIN TX DUP T Push M/CALL MW for 1 sec. MAIN TX DUP T M M M HM-133 operation: Push to select memory mode. Select memory channel. Push then push for 1 sec. 31 MEMORY OPERATION D Memory/callcall/memory q Select the memory/call channel to be transferred. Push the desired band's [M/CALL·MW] several times to select memory mode or call channel, then rotate the same band's [DIAL] to select the desired memory or call channel. w Push the same band's [M/CALL·MW] for 1 sec. · "!" indicator and "­ ­" indication blink, and shows VFO conditions. 5 MR/CALL MW [Y]/[Z] z Select the memory/call channel to be transferred. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. [. . . ] 20 A fuse 12 72 13 D GENERAL SPECIFICATIONS AND OPTIONS D TRANSMITTER · Modulation system · Output power · Max. frequency deviation · Spurious emissions · Microphone connector : Variable reactance frequency modulation : VHF 50/15/5 W (approx. ) UHF 35/15/5 W (approx. ) : ±5. 0 kHz (wide) ±2. 5 kHz (narrow: Left band only) : Less than ­60 dB : 8-pin modular (600 ) I Specifications 144­146 MHz, 430­440 MHz 144­146 MHz, 430­434 MHz, 435­438 MHz · Type of emission : FM, AM (Receive only) · Number of memory channels : 212 (incl. 10 scan edges and 2 calls) · Frequency resolution : 5, 10, 12. 5, 15, 20, 25, 30, 50 kHz · Operating temperature range : ­10°C to +60°C · Frequency stability : ±10 ppm (­10°C to +60°C) · Power supply requirement : 13. 8 V DC ±15% · Current drain (at 13. 8 V DC: approx. ): Transmit at 50 W 12 A Receive standby 1. 2 A (simultaneous receive) max. audio 1. 8 A · Antenna connector : SO-239 (50 ) · Dimensions (proj. [. . . ]