User manual ICOM IC-27H

[. . . ] If an incorrect connection is made after cutting, the transceiver might be damaged. NEVER place the transceiver where normal operation of the vehicle may be hindered or where it could cause bodily injury. Other microphones have different pin assignments and may damage the transceiver. Versions of the IC-27H/F320/F410/F420 which display "CE" on the serial number seal, comply with the essential requirements of the 89/336/EEC directive for Electromagnetic Compatibility. SmarTrunk IITM is a Trademark of SmarTrunk Systems, Inc. i TABLE OF CONTENTS DO NOT use or place the transceiver in areas with temperatures below ­30°C or above +60°C or, in areas subject to direct sunlight, such as the dashboard. IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i EXPLICIT DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] · When the optional UT-105 is installed, push one or more times to select a channel bank for conventional channels or SmarTrunk IITM channels. SCAN START/STOP KEY Push this key to start scanning; and push again to stop. Push and hold this key to indicate the scan group, then push to select the desired group. TAG I Programmable function keys The following functions can be assigned to [P0], [P1], [P2], [P3], [ ] and [ ] programmable function keys. Consult your Icom Dealer or System operator for details concerning your transceivers programming. In the following explanations, programmable function names are bracketed, the specifc switch used to activate the function depends on programming. CH UP CH DN PRI A PRI B BANK SCAN CH UP AND DOWN KEYS · Select an operating channel. · Select a transmit code channel after pushing the [TX CH] key. · Select a scan group after pushing and holding the [SCAN] key. CH 1 CH 2 CH 3 CH 4 OPERATING CHANNEL KEYS Select an operating channel directly. SCAN TAG KEY Adds or deletes the selected channel to the scan group. BEEP Push to turn the beep tones ON/OFF. BEEP 3 PANEL DESCRIPTION LOCK KEY Electronically locks all programmable keys except the following: · [CALL] (incl. MONITOR KEY Activates one of (or two of) the following functions on each channel independently: · Push and hold the key to unmute the channel (audio is emitted; `Audible' condition). · Push the key to toggle the mute and unmute conditions (toggles `Audible' and `Inaudible'). · Push the key to mute the channel (sets to `Inaudible' only). e When receiving a call, adjust the volume [UP] or [DOWN] to a comfortable listening level. D Transmitting notes TRANSMITTING: r Take the microphone off hook. · 5-tone mute may be released (the `audible' condition is selected and " " appears). · A priority channel may be selected automatically. · Transmit inhibit function The transceiver has several lockout/inhibit functions which restrict transmission under the following conditions: · The channel is in mute condition (`Inaudible' condition; " does not appear). " t Wait for the channel to become clear. · The channel is busy when " " appears. y Push the [CALL] key when initiating a call from your side. · Coded audio may be heard from the transceiver, then " " appears. · This operation may not be necessary depending on your signaling system. Ask your System Operator or Dealer. u While pushing and holding [PTT], speak into the microphone at your normal voice level. i Release [PTT] to receive. · Time-out timer After continuous transmission for a pre-programmed period, the time-out timer is activated causing the transceiver to stop transmitting and automatically select receive. > EXTERNAL SPEAKER JACK Connect a 4­8 external speaker, if desired. fi OPTIONAL CABLE (OPC-617) Connect an external modem unit, LCD backlight control, etc. 5 3 I Supplied Accessories 1 2 3 4 LCD-STICKER 6 7 8 9 0 A B C q Microphone . . . . . . . . . . . . . . . . . . . . . . 1 (Some versions may not be supplied with a microphone) w Microphone hanger and screw set . . . . . . . . . . . . . . . . . . . . . 1 r DC power cable . . . . . . . . . . . . . . . . . 1 IC-27H/F410: OPC-345 IC-F320/F420: OPC-346 u Mounting screw (M5×12) . . . 2 IC-27H/F410: 15 A IC-F320/F420: 20 A t Mounting bracket . . . . . . . . . . . . . . [. . . ] e Receiving a dispatch call is indicated by the same threebeep sequence. · It is not necessary to push [M] to answer a dispatch call. D Turbo SpeeDial To automatically dial a commonly used number with one push: · Push one of the turbo SpeeDials ([A], [B], [C] or [D]). D Emergency call Push [0], [M] to initiate an emergency call. · Contact your dealer for details. 14 4 OPTIONAL SmarTrunk IITM OPERATION D Clear channel alerting If all channels are busy, the transceiver automatically begins searching for an open channel and beeps every ten seconds. When two short beeps (low-pitched, then high-pitched) are heard, a channel is available. Push [M], [M] immediately to redial the last number. NOTE: For additional operating instructions, contact your Dealer or System Operator. 15 OPTIONS EXTERNAL SPEAKERS SP-5 Large speaker for good audio quality. input power: 5 W 5 UT-96 5-TONE UNIT Provides 2-tone/5-tone signaling . SP-10 Compact and easy-to-install. [. . . ]