User manual ICOM IC-2350H

[. . . ] Safe driving requires your full attention-- anything less may result in an accident. NEVER connect the transceiver to a power source of more than 16 V DC. This will ruin the transceiver. IMPORTANT READ ALL INSTRUCTIONS pletely before using the transceiver. carefully and com- SAVE THIS INSTRUCTION MANUAL--This instruction manual contains important operating instructions for the IC-2350H/-T. NEVER connect the transceiver to a power source using reverse polarity. [. . . ] Push [SET] one or more times until "T" and "rT" appears for repeater use; or until "T SQL" and "CT" appears for tone squelch or pocket beep use. · Push [MONI] to reverse the order of selection. · Cancel the DTMF memory encoder function in advance, if necessary. 45) Å Push [FSET] one or more times until "T" and "rT" appears for repeater use; or until "T SQL" and "CT" appears for tone squelch or pocket beep use. · Pushing [GENT] reverses the order of selection. · Cancel the DTMF memory encoder function in advance, if necessary. 45) Ç Push [Y] or [Z] to select and set the desired frequency. · Pushing and holding [Y] or [Z] changes the frequency continuously. Rotate the tuning dial to select and set the desired frequency. É Push [ECLR] to exit set mode. · Subaudible tone frequency list 67. 0 69. 3 71. 9 74. 4 77. 0 79. 7 82. 5 85. 4 88. 5 91. 5 94. 8 97. 4 100. 0 103. 5 107. 2 110. 9 114. 8 118. 8 123. 0 127. 3 131. 8 136. 5 141. 3 146. 2 151. 4 156. 7 159. 8 162. 2 165. 5 167. 9 171. 3 173. 8 177. 3 179. 9 183. 5 186. 2 189. 9 192. 8 196. 6 199. 5 Push [V/MHz] to exit set mode. NOTE: The subaudible tone encoder frequency can be set in a memory channel temporarily. However, the set contents are cleared once the memory/call mode is selected. To store the tone frequency permanently, overwrite the channel information. (unit: Hz) 203. 5 206. 5 210. 7 218. 1 225. 7 229. 1 233. 6 241. 8 250. 3 254. 1 23 5 REPEATER OPERATION Ä Set the mode/channel you wish to set the offset frequency to, such as VFO mode, memory/call channel or scratch pad memory. · The offset frequency can be independently programmed into each mode or channel. s Offset frequency DUP 1 5 9 USING SET MODE SET B The display shows that a 0. 6 MHz (600 kHz) frequency is set. Å Push [FSET] one or more times until "DUP" appears as shown at left. Select the mode/channel you wish to set the subaudible tone frequency to, such as VFO mode or memory/call channel. · The offset frequency can be individually programmed into each mode or channel. · Pushing [GENT] reverses the order of selection. · Cancel the DTMF memory encoder function in advance, if necessary. 44) Ç Push [Y] or [Z] to select and set the desired frequency. · Selectable step increment is the same as the preset tuning step. 16) · Pushing and holding [Y] or [Z] changes the frequency continuously. Push [SET] one or more times until "DUP" appears and flashes as shown above. · Push [MONI] to reverse the order of selection. and continue pushing X 1 5 9 1 5 9 M M M 27 6 MEMORY OPERATION s Programming a memory channel via the microphone MW The microphone can also be used to program memory channels. Ä Set the desired frequency in VFO mode: Push [VFO] to select VFO mode. offset frequency, duplex direction, subaudible tone encoder ON/OFF and its frequency), if necessary. Å Push [FUNC], then [EMW] momentarily. Push [Y] or [Z] to select the memory channel (direct numeral input cannot be used). 3 beeps may sound and the VFO contents (including the subaudible tone frequency, etc. ) are programmed. Memory channel number advances when continuing to push [MW] after programming. [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 via the microphone. Push MONI VFO 1 8 HIGH 4 7 MID 5 0 MW ENT C DUP+ DUP Push FUNC then CLR A momentarily 1 5 9 1 5 9 1 5 9 M MW Push Push FUNC then CLR A for 1 sec. and continue pushing 5 9 5 9 X 1 5 9 1 1 M M M 28 MEMORY OPERATION 6 s Transferring memory contents This function transfers a memory channel's contents to VFO (or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency, etc. S. MW MW MW Ä Set the memory channel to be transferred: Push [MR] to select memory mode. Push [Y] or [Z] to select the memory channel; or push [GENT] then push the desired memory channel number (3 digits) to select the memory channel directly. Å Push [FUNC] then [EMW] momentarily, then push [Y] or [Z] to select another memory channel to transfer. · To transfer to the VFO, push [FUNC] then push and hold [EMW] instead of pushing momentarily. Push DUP T 1 5 9 for 1 sec. DUP T 1 5 9 M Ç Push [FUNC] then [EMW] for 1 sec. to transfer. MW FUNC + CLR A Select the memory channel to be programmed. Select memory mode by pushing [M/CALL] once or twice ("!" appears). Push [S. MW] momentarily, then rotate the tuning dial to select another memory channel to transfer. · To transfer to the VFO, push and hold [(S. MW)MW] instead of pushing momentarily. Push and hold [(S. MW)MW] to transfer when a momentary push was used in the previous step. 29 6 MEMORY OPERATION s Memory clearing Contents of programmed memories can be cleared (blanked), if desired. [. . . ] · Priority watch is paused on the watching frequency. · Check, and if necessary, replace the feedline or p. 42 60 Frequency cannot be set · The frequency lock function is activated. · Priority watch is paused on the watching frequency. · Push and hold [LOCK] to deactivate the frequency p. · Push [(M/CALL)PRIO] to resume the watch. MAINTENANCE 15 PROBLEM POSSIBLE CAUSE SOLUTION · Rotate the tuning dial to check whether the channel has been programmed or not. [. . . ]