User manual ICOM IC-2340H-A-E

[. . . ] We want to take a couple of moments of your time to thank you for making your IC-2340H-A-E your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-2340H-A-E. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-2340H-A-E. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!WORD D FEATURES 65 W* of high transmit output power (except Korea/Taiwan versions) Tone squelch, DTCS squelch standard Dual color (amber & green) LCD backlight Remote control microphone available (optional for some versions) Optional Digital modulator/demodulator Optional DTMF decoder Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i PRECAUTION RWARNING RF EXPOSURE!If you have any questions regarding RF exposure and safety standards please refer to the Federal Communications Commission Office of Engineering and Technology's report on Evaluating Compliance with FCC Guidelines for Human Radio frequency Electromagnetic Fields (OET Bulletin 65) RWARNING! [. . . ] Push [BANK OPT ] then rotate [DIAL] to select the desired memory bank. · Bank initial blinks. y Repeat steps q to t for transferring or erasing an another banks contents. Push [BANK/OPTION], then select the deSET YZ sired memory bank via [Y]/[Z]. Push [CLR A(MW)] to select the bank then YZ select the desired contents via [Y]/[Z]. c Push [SET B(D-OFF)] or [ENT C(T-OFF)] several times until "BAK" appears. YZ v Push [Y]/[Z] to select the desired bank initial to transfer or erase. BANK · Select "-- --" indication when erasing the contents from the bank. 5 Push [BANK OPT ] to select the bank then rotate [DIAL] to select the desired contents. · Bank initial stops blinking. w Push [SET LOCK ] enter the set mode. e Push [SET] or [MONI] several times until "BAK" appears. · Bank initial appears. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz b Push [CLR A(MW)] to set the bank and exit set mode. n Repeat steps z to b for transferring or erasing an another banks contents. r Rotate [DIAL] to select the desired bank initial to transfer or erase. · Select "­ ­" indication when erasing the contents from the bank. t Push any key other than [SET] or [MONI] to transfer or erase. 34 6 CALL CHANNEL OPERATION I Call channel transferring q Push [M/CALL PRIO ] several times to select the call channel. · "C" appears. I Call channel selection Push [M/CALL PRIO ] once or twice to select the call channel. Appears DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · "C" appears instead of memory channel number indication. · Push [M/CALL PRIO ] to return to memory mode, or push [V/MHz SCAN ] to select VFO mode. w Push [S. MW MW ] momentarily, then rotate [DIAL] to select the memory channel to transfer the contents to. · "M" indicator and memory channel number blink. · To transfer to the VFO, push [S. MW MW ] for 1 sec. SET MONI LOW TONE M/CALL V/ MHz e Push [S. MW MW ] for 1 sec. to transfer when a momentary push was used in the previous step. · If channel names have been programmed into the call channel, the names are also transferred. MR/CALL MR/CALL Push [MR/CALL] for 1 sec. · The memory channel readout blinks the scan type as follows: v Push [SET B(D-OFF)] to switch full and programmed scan (P1, P2 and P3). b To stop the scan push [SCAN 2(T-SCAN)] or [CLR A(MW)]. r Push [SET LOCK ] to switch full and programmed scan (P1, P2 and P3). t To stop the scan, push [SET LOCK ] or [V/MHz SCAN ]. · During full scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During programmed scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During memory scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During Bank scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz ( SET ) to select full, Push band* (A1, AA) or programmed scan (P1, P2 and P3) in sequence. (*Depends on versions) A1 : FM band (136­174 MHz) AA : AM band (118­136 MHz) LOCK Indicates scan edge channels. · P1 stands for 1A/1b · P1 to P3 are available when they are programmed, and ( SET ) . switches with LOCK When AM and FM frequencies are programmed into memory channel disorderly, memory scan takes a lot of time (very slow). In this case, assign AM and FM frequencies into the separate bank respectively. And using the bank scan is helpful. 38 7 SCAN OPERATION I Scan edges programming Scan edges can be programmed in the same manner as memory channels. Scan edges are programmed into scan edges, 1A/1b to 3A/3b, in memory channels. q Set the edge frequency of the desired frequency range in VFO mode: Set the frequency using [DIAL]. w Push [S. MW MW ] momentarily. · "M" indicator and channel number blink. r Push [S. MW MW ] for 1 sec. [. . . ] audio 1. 0 A · Antenna connector : SO-239 (50 ) · Dimensions (proj. not included) : 140(W) × 40(H) × 146(D) mm 51/2(W)×19/16(H)×53/4(D) in · Weight (approx. ) : 1. 25 kg; 2 lb 12 oz RECEIVER · Receive system · Intermediate frequencies · Sensitivity (at 12 dB SINAD) · Squelch sensitivity (threshold) · Selectivity [Wide] : Double-conversion superheterodyne : 1st: 21. 7 MHz, 2nd: 450 kHz : 0. 14 µV typical : 0. 1 µV typical : More than ±6 kHz/6 dB Less than ±14 kHz/60 dB [Narrow] More than ±3 kHz/6 dB Less than ±9 kHz/55 dB · Spurious and image rejection : 75 dB typical · AF output power (at 13. 8 V DC) : More than 2. 4 W at 10% distortion with : 3-conductor 3. 5 (d) mm (1/8)/8 : 3-conductor 2. 5 (d) mm (1/8) an 8 load · Ext. Data connector TRANSMITTER · Modulation system · Output power (*approx. , Korea version) Some version only : Variable reactance frequency mod. low Low 65 W (50 W) 24 W 25 W* 10 W* 5 W* 10 W* N/A 5 W* 13 14 All stated specifications are subject to change without notice or obligation. 88 15 MAINTENANCE If your transceiver seems to be malfunctioning, please check the following points before sending it to a service center. [. . . ]