User manual ICOM IC-1271A-E

[. . . ] This radio has been tested and complies with the FCC RF exposure limits for "Occupational Use Only". In addition, your Icom radio complies with the following Standards and Guidelines with regard to RF energy and electromagnetic energy levels and evaluation of such levels for exposure to humans: · FCC OET Bulletin 65 Edition 97-01 Supplement C, Evaluating Compliance with FCC Guidelines for Human Exposure to Radio Frequency Electromagnetic Fields. · American National Standards Institute (C95. 1-1992), IEEE Standard for Safety Levels with Respect to Human Exposure to Radio Frequency Electromagnetic Fields, 3 kHz to 300 GHz. · American National Standards Institute (C95. 3-1992), IEEE Recommended Practice for the Measurement of Potentially Hazardous Electromagnetic Fields­ RF and Microwave. [. . . ] 26­29 ` MB-93 contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 ` To attach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 ` To detach . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28 7 OPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30­33 v ACCESSORIES I Supplied accessories 1 1 The following accessories are supplied: Qty. Ask your dealer for details. q w e t r 1 1 ACCESSORIES I Accessory attachments D Flexible antenna Connect the supplied flexible antenna to the antenna connector. CAUTION: · NEVER HOLD by the antenna when carrying the transceiver. · Transmitting without an antenna may damage the transceiver. 2 ACCESSORIES 1 1 ï Battery pack To attach the battery pack: Slide the battery pack on the back of the transceiver in the direction of the arrow (q), then lock it with the battery release button. · Slide the battery pack until the battery release button makes a `click' sound. To release the battery pack: Push the battery release button in the direction of the arrow (w) as shown below. NEVER release or attach the battery pack when the transceiver is wet or soiled. This may result in water or dust getting into the transceiver/battery pack and may result in the transceiver being damaged. q w 3 1 ACCESSORIES ï Jack cover Attach the jack cover when the optional speaker-microphone is not used. To attach the jack cover: To detach the jack cover: q Attach the jack cover to the q Unscrew the screws with a [SP MIC] connector. When turning the power ON, the transceiver automatically starts scanning. Scanning stops when receiving a call. 12 CONVENTIONAL OPERATION 3 I Call procedure When your system employs tone signalling (excluding CTCSS and DTCS), the call procedure may be necessary prior to voice transmission. The tone signalling employed may be a selective calling system which allows you to call specific station(s) only and prevent unwanted stations from contacting you. q Select the desired TX code channel or 2/5-tone code according to your System Operator's instructions. · This may not be necessary depending on programming. 3 w Push the call key (assigned to one of the dealer programmable keys. ) (p. 11) e After transmitting a 2/5-tone code, the remainder of your communication can be carried out in the normal fashion. Selective calling Non-selective calling 13 3 CONVENTIONAL OPERATION I Receiving and transmitting NOTE: Transmitting without an antenna may damage the transceiver. 2 for antenna attachment. Receiving: q Rotate [VOL] to turn power ON. w Toggle [CHANNEL SWITCH] (IC-F14S/F24S), rotate [CHANNEL SELECTOR] (IC-F14/F24/F26-L) or push one of [MR-CH 1] to [MR-CH 4] key to select a channel. For IC-F14S/F24S: The memory channels 3 and 4 are available when [MR-CH 3] and [MR-CH 4] keys are assigned. e When receiving a call, adjust the audio output level to a comfortable listening level. Transmitting: Wait for the channel to become clear to avoid interference. q While pushing and holding [PTT], speak into the microphone at a normal voice level. · When a tone signalling system is used, the call procedure described on p. Hold the microphone 5 to 10 cm (2 to 4 inches) from your mouth, then speak into the microphone at a normal voice level. 14 CONVENTIONAL OPERATION 3 D Transmitting notes · Transmit inhibit function The transceiver has several inhibit functions which restrict transmission under the following conditions: - The channel is in mute condition. · Time-out timer After continuous transmission for the pre-programmed time period, the time-out timer activates, and causes the transceiver to stop transmitting. [. . . ] The following items are additionally required: · One AD-106 (purchase separately). · An AC adapter (may be supplied with BC-119N depending on version) or the DC power cable (OPC-515L/CP-17L). Transceiver Turn power OFF Battery pack AC adapter (Not supplied with some versions. ) AD-106 charger adapter is installed in BC-119N. Optional OPC-515L (for 13. 8 V power source) or CP-17L (for 12 V cigarette lighter socket) can be used instead of the AC adapter. IMPORTANT!: Ensure the guide lobs on the battery pack are correctly aligned with the guide rails inside the charger adapter. Guide rails Lobs 24 BATTERY CHARGING 5 D Rapid charging with the BC-121N+AD-106 The optional BC-121N allows up to 6 battery packs to be charged simultaneously. [. . . ]