User manual ICOM FP-601G

[. . . ] INSTRUCTION MANUAL MARINE PLOTTER/SOUNDER FP-561 COMBINE MARINEPLOTTER/SOUNDER fp-561 Information provided by this product includes are not legal Electronic charts navigation-aid data. Consult nautical consult current Always carry and charts in addition to the data when making a official charts frequently. decision on navigation. INTRODUCTION Thank you very much for purchasing the FP-561. The FP-561 is an advanced navigation and fishfinding system of compact design into which a marine navigator with a built-in GPS receiver and a fishfinder are integrated. [. . . ] You will return to the previous screen. ´ Specifying the color of lights 5 SCREEN SETTING DISP MODE BKG COLOR LAND SEA NAME D CON 5m D CON 10m D CON 20m LIGHT GRID DISP MAPS 1 BLUE YELL BLUE WHIT LBLU LBLU LBLU RED BLUE WHIT 2 CSLN OFF OFF OFF OFF OFF OFF OFF CLR ADJ CANC SET SEL SET 80. 0FT The color of lights can be selected from among seven available colors. w Select "Plotter Menu" using the [UP] or [DOWN] key and press the [SET] key. e Select "LIGHT" using the [UP] or [DOWN] key and press the [SET] key. t Select the desired color from among available colors (White (WHIT), Yellow (YELL), Light blue (LBLU), Purple (PURP), Red, Green (GREE), Blue) using the [UP] or [DOWN] key and press the [SET] key. * When you select "OFF" and press the [SET] key, lights are not displayed. You will return to the previous screen. 32 8 r PLOTTER MODE q DATA COLOR SETTING Ï Specifying the color of map border 5 SCREEN SETTING DISP MODE BKG COLOR LAND SEA NAME D CON 5m D CON 10m D CON 20m LIGHT GRID DISP MAPS 1 BLUE YELL BLUE WHIT LBLU LBLU LBLU RED BLUE WHIT 2 CSLN OFF OFF OFF OFF OFF OFF OFF CLR ADJ CANC SET SEL SET 80. 0FT The color of map border can be selected from among seven available colors. w Select "Screen Setting" using the [UP] or [DOWN] key and press the [SET] key. e Select "DISP MAPS" (display maps) using the [UP] or [DOWN] key and press the [SET] key. t Select the desired color from among available colors (White (WHIT), Yellow (YELL), Light blue (LBLU), Purple (PURP), Red, Green (GREE), Blue) using the [UP] or [DOWN] key and press the [SET] key. * When you select "OFF" and press the [SET] key, map border are not displayed. y When you finish setting the color of map border, press the [MENU] key. You will return to the previous screen. Specifying the display mode 5 SCREEN SETTING DISP MODE BKG COLOR LAND SEA NAME D CON 5m D CON 10m D CON 20m LIGHT GRID DISP MAPS 1 BLUE YELL BLUE WHIT LBLU LBLU LBLU RED BLUE WHIT 2 CSLN OFF OFF OFF OFF OFF OFF OFF These color settings can be memorized and selected from two display modes. w Select "Plotter Menu" using the [UP] or [DOWN] key and press the [SET] key. e Select "DISP MODE" (display mode) using the [LEFT] or [RIGHT] key and press the [SET] key. You will return to the previous screen. CLR SEL CANC SET SET 80. 0FT 33 r PLOTTER MODE q POSITIONING DEVICE 9 (9) Selection of positioning device 5 POSITIONING MENU POS EQUIP GPS NMEA POS CORR GOTOCURSOR LAT N0. 000 LON E0. 000 AVERAGING 1 OFF DGPS# POSITIONING INFO# 0 10 20 30 40 CLR SEL CANC H SET SET 80. 0FT There are two options in receiving the latitude and longitude data of the current ship position. w Select "Positioning Menu" using the [UP] or [DOWN] key and press the [SET] key. e Select "POS EQUIP" (positioning equipment) using the [UP] or [DOWN] key and press the [SET] key. r Select "GPS" or "NMEA" using the [LEFT] or [RIGHT] key. · When you select "GPS", positioning data received by the supplied GPS receiver is used to pinpoint the current ship position. · When you select "NMEA", positioning data received via the external NMEA input port is used to pinpoint the current ship position. * Selecting "NMEA" disables "DGPS" and "Positioning Information" to be selected. t When you finish selecting the positioning device, press the [MENU] key. [. . . ] q Area where the possibility of on-screen voids due to air bubbles or water turbulence is minimized; w Area that resists being exposed to noises from the engine; e Area where the transducer is kept horizontal even if the ship runs at high speed; (The optimum installation position of the transducer is said to be at a distance of a half or one-third of the ship length from the stern for low-speed small ships, and to be located close to the stern for high-speed ships. ) r Area where the bottom plate is the thinnest in the vicinity of the stern (for innerhull type transducer; the ultrasonic decays when it passes through the bottom plate). Installation example of EX-1010 To the TRANSDUCER terminal on the real panel of FP-561 Bottom plate of the ship ¡ Do not plug or unplug a cable into of from the TRANSDUCER connector. ¡ A transducer must be installed by a shipbuilder or an expert installer. 72 6 INSTALLATION PROCEDURE 6-6 Connecting an external navigator An external navigation equipments can be connected to the NMEA connector on the rear panel of the system. Connect a 4-pin microphone connector to the NMEA connector and plug the data line in the 1-pin connector and the data return line in the 2-pin connector. When using an external navigator, set "Positioning Equipment" to "NMEA" on the Positioning Menu screen ( P. [. . . ]