User manual ICOM AT-160

[. . . ] and the Icom logo are registered trademarks of Icom Incorporated (Japan) in Japan, the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. All other products or brands are registered trademarks or trademarks of their respective holders. TABLE OF CONTENTS IMPORTANT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . i TABLE OF CONTENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ii 1 PREPARATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1­2 Programmable function keys . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 2 BIIS 1200 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3­12 BIIS 1200 operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 BIIS display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Receiving a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Transmitting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Position data transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Stun function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 BIIS ANI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 Horn output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Printer connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 3 dPMR OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13­27 dPMR operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 dPMR display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Receiving a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Transmitting a call . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Transmitting a command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Position data transmission. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Status message transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26 Horn output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 Printer connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27 ii 1 PREPARATION Programmable function keys The following functions can be assigned to [UP], [DOWN], [P0], [P1], [P2], [P3] and [P4] programmable function keys. [. . . ] Ask your dealer for details. w When the time period ends, the transceiver automatically starts an Emergency call cycle, once or repeatedly, depending on the pre-programmed repeat cycle setting. e In an Emergency call cycle, the transceiver automatically transmits Status 22 (Emergency) to inform the dispatcher that the user is in an emergency situation. · "WAIT" appears while transmitting. · "OK" is displayed when an acknowledgement is received. · "FAILED" is displayed when no acknowledgment is received. NOTE: Depending on the pre-programmed settings, the transceiver does not transmit Status 22 in the repeated cycles. r After the Emergency call cycles have ended, the transceiver automatically returns to the stand-by mode. · To exit the emergency mode manually, turn OFF the power, and turn ON it again. 10 2 BIIS 1200 OPERATION Position data transmission When a GPS receiver is connected to the transceiver, the position data (longitude and latitude) can be automatically transmitted. The position data is transmitted: · When Status 24 (GPS request) is received. · When [PTT] is released. - Set the `Send with Logoff' item to "Enable. " Stun function If a call is received with a specified ID, set as the killer ID, the stun function is activated and the transceiver is disabled. In that case, entering the password is necessary to reactivate the transceiver. BIIS ANI Your own ID can be transmitted each time [PTT] is pushed (log-in) or released (log-off) during Individual or Group call communications. By receiving an ANI, the communication log can be recorded when using a PC dispatch application. In addition, when using the ANI with the Log-in function, the PTT Side Tone function can be used to inform you that the ID is sent and communication can begin. · After sending a status message. - Set the `Send with Status' item to "Enable. " · After sending an SDM. - Set the `Send with SDM' item to "Enable. " · After sending Status 22 (Emergency). - Set the `Send with Emergency' item to "Enable. " · By the Automatic Position Transmission function. When the function is activated, the transceiver automatically transmits position data according to the `Time Marker' and `Interval Timer' settings. - Set the `Auto' item to "Enable. " NOTE: Configure the position data transmission settings using the CS-F3160/F5060 (dPMR) cloning software. NOTE: If the transceiver receives a Stun, Kill, or Revive command from a station other than the specified ones, the call will be ignored, and the transceiver will not be stunned, killed, or revived. In that case, receiving a Revive command or inputting the password*2 is necessary to operate the transceiver again. *1 Depending on the pre-programmed settings, receiving a Stun command inhibits only transmission, but the transceiver still can receive. *2 Depending on the pre-programmed settings. D Receiving an SDM q When an SDM is received: · Rings sound. · The calling station's ID (or name) and the SDM are displayed. Appears The received SDM Message 1 ID 0000001 Calling station's ID NOTE: When the SDM includes more than 12 characters, it automatically scrolls. · Push [Status Up] or [Status Down] to stop scrolling, or manually scroll the message. RETURN TO OFFICE ID 0 0 0 0 0 0 1 Scrolls w Push [Clear] to return to the stand-by mode. When a Kill command is received, the transceiver is disabled. In that case, re-programming the transceiver is necessary to operate the transceiver again. D Receiving a Status Polling call If a Status Polling call is received, the transceiver will automatically transmit its current status. 15 dPMR OPERATION D Receiving an Ambience Listening call If an Individual call with an Ambience Listening command is received from a specified station, the transceiver will automatically transmit its microphone audio. · The HM-148G or HM-152 HAND MICROPHONE is required. 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 D Talk back function The Talk Back function allows you to select the same call mode (Analog or Digital) as the received call. If the received call is a digital signal, the Talk Back function is activated for Voice and Emergency calls, and depending on the pre-programmed settings, also for status messages and SDM. When the channel type is "Mixed-Digital" After receiving an analog signal, "ANALOG" is displayed during the Talk Back timer period, depending on the pre-programmed settings. When [PTT] is pushed before or during the Talk Back timer period, you can transmit an analog signal. When the channel type is "Mixed-Analog, " "Mixed-Digital" or "Digital" After receiving a digital signal, the calling station's ID or the Talkgroup ID is displayed until receiving a `Disconnect' signal, depending on the pre-programmed settings. [. . . ] · When no acknowledgement is received, an error beep sounds and "FAILED" is displayed. NOTE: Depending on the pre-programmed setting, the transceiver does not transmit the digital signal in the repeated cycles. 23 dPMR OPERATION 3 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Transmitting a command The following Individual calls allow you to send special commands. These calls will function if you are designated as a specific station. Ask your dealer for details. D Transmitting a Stun Call A Stun call allows you to send a command that will stun the target station. q Push [dPMR Button] to enter the ID selection mode. · The pre-programmed ID is displayed. D Transmitting an Ambience Listening Call An Ambience Listening call allows you to send a command that will require the target station to transmit its microphone audio. [. . . ]