User manual ICOM AT-130E

[. . . ] We want to take a couple of moments of your time to thank you for making your IC-V82/U82 your radio of choice, and hope you agree with Icom's philosophy of "technology first. " Many hours of research and development went into the design of your IC-V82/U82. IMPORTANT READ ALL INSTRUCTIONS carefully and completely before using the transceiver. SAVE THIS INSTRUCTION MANUAL-- This instruction manual contains important operating instructions for the IC-V82/U82. EXPLICIT DEFINITIONS DEFINITION Personal injury, fire hazard or electric shock R WARNING!WORD D FEATURES 7 W*-- high transmit output power (*IC-V82, 5 W for AT-130E) CTCSS and DTCS encoder/decoder standard Optional digital modulator/demodulator Optional DTMF decoder Icom, Icom Inc. and the logo are registered trademarks of Icom Incorporated (Japan) in the United States, the United Kingdom, Germany, France, Spain, Russia and/or other countries. i PRECAUTIONS RWARNING!NEVER hold the transceiver so that the antenna is very close to, or touching exposed parts of the body, especially the face or eyes, while transmitting. [. . . ] Each memory channel, 0 to 199, may be assigned to one of the banks for easy memory management. q Push [C·MR] to select memory mode. Push C MR Memory bank setting q Push [C·MR] to select memory mode, then select the deY Z sired memory channel via [Y] or [Z]. Push C MR w Push [A·FUNC] and [8·SET] to enter SET MODE. [VOL] 6 w Push [A·FUNC] and [#·BANK] to enter memory bank selection. · Bank indicator blinks. [VOL] Y Z e Push [Y] or [Z] several times until "bAk" appears. · "­ ­" indication blinks as follows. A FUNC e Rotate [VOL] to select the desired bank, A to J. · Banks that have no programmed contents are skipped. A FUNC r Rotate [VOL] to select the desired bank. ENT SET BANK ENT 8 r Push [·ENT lect the bank. ] (or [D·CLR]) to se- · Indicator stops blinking. Y Z t Push [Y] or [Z] to select the channel in the bank. · No channel numbers are displayed for memory bank operation. t Push [·ENT ] (or [D·CLR]) to assign the channel to the bank and return to regular memory condition. y Repeat steps q to t to assign another memory channel to the same or another bank. 16, 65) in INITIAL SET must be selected "FR, " otherwise the memory bank operation cannot be performed. 25 y To return to regular memory condition, push [A·FUNC] and [#·BANK] to enter memory bank mode, then push [·ENT ] (or [D·CLR]). MODE 6 MEMORY/CALL OPERATION Transferring bank contents Contents of programmed memory banks can be cleared or transferred to another bank. INFORMATION: Even if the memory bank contents are cleared, the memory channel contents still remain programmed. Push [A·FUNC] and [#·BANK], then rotate [VOL] to select the desired memory bank. · Bank indicator blinks. [VOL] w Push [A·FUNC] and [8·SET] to enter SET MODE. [VOL] Y Z e Push [Y] or [Z] several times until "bAk" appears. · Bank indicator appears. A FUNC r Rotate [VOL] to select the desired bank to receive the transferred information or erase the bank contents. · Select "­ ­" indication when erasing the contents from the bank. ENT SET 8 A FUNC Push [·ENT ] (or [D·CLR]) to Y select the bank then push [Y] Z and [Z] to select the desired contents. · Bank indicator stops blinking. t Push [·ENT ] (or [D·CLR]) to transfer or erase, and return to regular memory mode. y Repeat steps q to t for transferring or erasing an another bank's contents. BANK ENT 26 DTMF MEMORY Programming a DTMF code sequence The transceiver has 16 DTMF memory channels (d0 to dF) for storage of often-used DTMF code sequence of up to 24 digits. q Push [A·FUNC], then push [0·OPT] to enter OPTION SET MODE. · Rotate [VOL] to select "dtm. OF, " if necessary. Or when an opY Z tional UT-118 DIGITAL UNIT is installed, push [Y] or [Z] several times until "dtm. OF" appears. 14, 65) Push MONI PWR A FUNC B CALL C MR D CLR 8 A FUNC SCAN 5 TONE 1 P. BEEP 2 T. SCAN 3 BANK e Push [D·CLR] to stop the scan. DUP 4 SCAN 5 SKIP 6 OPT 0 PRIO 7 SET 8 H/M/L 9 ENT · Bank scan --Select the desired bank in step q above. q Push [A·FUNC] and [#·BANK] to select memory bank mode. w Rotate [VOL] to select the desired bank, A to J. e Push [·ENT ] (or [D·CLR]) to select the bank. 31 8 SCAN OPERATION Skip channels In order to speed up the scan rate, you can select memory channels you don't wish to scan as skip channels. q Push [C·MR] to select memory mode, if necessary. · "X" appears. Priority watch Priority watch checks for signals on "priority channels" while operating on a VFO frequency. D Memory or call channel watch While operating on a VFO frequency, memory or call channel watch monitors for signals in the selected memory or call channel every 5 sec. e Push [A·FUNC], then push [7·PRIO] to start watching. w Select a memory channel to set as a skip channel. ePush [A·FUNC] and [6·SKIP] to toggle the skip setting ON and OFF. · "SKIP" appears when the channel is set as a skip channel. Push A FUNC SKIP 6 "SKIP" appears · VFO is displayed, then the decimal point ". ", on the frequency readout blinks. · When the signal is detected on the priority channel, the watching is suspended according to the setting of the scan resume condition. VFO frequency Memory channel 5 sec. 50 msec. r Push [D·CLR] to stop watching. 32 SCAN OPERATION D Memory scan watch While operating on a VFO frequency, memory scan watch monitors for signals in each memory channel in sequence, every 5 sec. q Push [C·MR] to select memory mode, if necessary. · "X" appears. 8 Scan resume condition USING SET MODE wPush [A·FUNC], then push [5·SCAN] to start the memory scan. e Push [A·FUNC], then push [7·PRIO] to start the watching. · VFO is displayed, then the decimal point ". ", on the frequency readout blinks. · When the signal is detected on the priority channel, the watching is suspended according to the setting of the scan resume condition. VFO frequency Mch 3 Mch 2 Mch 1 When a signal is received during scanning, the scan resume condition determines what action the transceiver takes. [. . . ] · BC-146 BATTERY CHARGER + BC-147 AC ADAPTER For regular charging of battery packs. · BC-119N DESKTOP CHARGER + AD-101 CHARGER ADAPTER For rapid charging of battery packs. · BC-121N MULTI-CHARGER + AD-101 CHARGER ADAPTER (6 pcs. ) For rapid charging of up to 6 battery packs (six AD-101's are required) simultaneously. Charging time: 1. 5 to 2 hrs. D OTHER OPTIONS · HM-75A/HM-131L SPEAKER-MICROPHONES Combination speaker-microphones that provide convenient operation while hanging the transceiver from your belt. [. . . ]