User manual ICOM 2200H

[. . . ] INSTRUCTION MANUAL VHF TRANSCEIVER i2200H This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom product. The IC-2200H VHF TRANSCEIVER is designed and built with Icom's superior technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] to program. · 3 beeps sound and the unit returns to VFO mode automatically. VFO/CALL MW [Y]/[Z] z Set the desired frequency in VFO mode. to program. · 3 beeps sound and the unit returns to VFO mode automatically. 6 [EXAMPLE]: Programming 145. 120 MHz into the call channel via the microphone. Push MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN to select VFO mode. DIGITAL PRIO AO BUSY Set the frequency. DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN Push MUTE NAR MID LOW LOCK , then momentarily. DIGITAL PRIO AO BUSY ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz Push MUTE NAR MID LOW LOCK until large "C" appears. DIGITAL PRIO AO BUSY Push MUTE NAR MID LOW then for 1 sec. SCAN DIGITAL PRIO AO BUSY ANM DUP T-SCAN PRIO SCAN LOCK ANM DUP T-SCAN PRIO SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz " "Beep " Beep " Beep " DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz 36 7 SCAN OPERATION I Scan types Scanning searches for signals automatically and makes it easier to locate new stations for contact or listening purposes. There are 3 scan types and 4 resume conditions to suit your operating needs. FULL SCAN (p. 38) Band edge Scan Band edge Repeatedly scans all frequencies over the entire band. Used as the simplest scan without any preliminary settings necessary. PROGRAMMED SCAN (p. 38) Band edge Scan edges Band edge Scan Jump Jump Repeatedly scans between two user-programmed frequencies. Used for checking for frequencies within a specified range such as repeater output frequencies, etc. 38) SKIP M1 M0 M 199 M6 M5 M2 M3 M4 SKIP Repeatedly scans memory channels except those set as skip channels. Used for oftencalled channels and for bypassing normally busy channels such as repeater frequencies. SCAN RESUME CONDITION (p. Timer scan Pausing 4 resume conditions are available: 3 timer scans and pause scan. When receiving a signal, pause scan pauses until the signal disappears; timer scans pause for 5, 10 or 15 sec. NOTE: A tone scan function is available to search for subaudible tones (e. g. when you want to find a subaudible tone frequency necessary to open a repeater). 37 SCAN OPERATION 7 I Scan start/stop D Preparation Scan resume condition (p. 41). SCAN 2 SET B z Push [VFO/LOCK] to select VFO mode for full/programmed scan; push [MR/CALL] to select memory mode for memory scan. · Push [BANK/OPTION] to select a bank for bank scan. D Operation q Select VFO mode for full/programmed scan with [V/MHz SCAN ]; or memory mode for memory scan with [M/CALL PRIO ]. · Select the desired bank with [BANK OPT ] for bank scan. x Set the squelch to the point where noise is just muted. c Push [SCAN 2(T-SCAN)] to start the scan. Y Z · Push [Y] or [Z] for 1 sec. also starts the scan. 7 w Set the squelch to the point where noise is just muted. to start the scan. · To change the scanning direction, rotate [DIAL]. · The memory channel readout blinks the scan type as follows: v Push [SET B(D-OFF)] to switch full and programmed scan (P1, P2 and P3). b To stop the scan push [SCAN 2(T-SCAN)] or [CLR A(MW)]. r Push [SET LOCK ] to switch full and programmed scan (P1, P2 and P3). t To stop the scan, push [SET LOCK ] or [V/MHz SCAN ]. · During full scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During programmed scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During memory scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN · During Bank scan DIGITAL PRIO AO BUSY MUTE NAR MID LOW LOCK ANM DUP T-SCAN PRIO SCAN SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz SET MONI LOW TONE M/CALL V/ MHz ( SET ) to select full, Push band* (A1, AA) or programmed scan (P1, P2 and P3) in sequence. (*Depends on versions) A1 : FM band (136­174 MHz) AA : AM band (118­136 MHz) LOCK Indicates scan edge channels. · P1 stands for 1A/1b · P1 to P3 are available when they are programmed, and ( SET ) . [. . . ] · Blown fuse. I Troubleshooting PROBLEM No power comes on. SOLUTION REF. · Check the connector pins. · A selective call or squelch function is activated such as pocket beep or tone squelch. Sensitivity is low and only · Antenna feedline or the antenna connector solder · Check, and if necessary, replace the feedline or sol- p. 14 No contact possible with · The other station is using tone squelch. 44 Repeater cannot be ac- · Wrong offset frequency is programmed. [. . . ]