User manual ICOM 208H

[. . . ] INSTRUCTION MANUAL VHF/UHF FM TRANSCEIVER i208H This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. FOREWORD Thank you for purchasing this Icom product. The IC-208H VHF/UHF FM TRANSCEIVER is designed and built with Icom's state of the art technology and craftsmanship. With proper care, this product should provide you with years of trouble-free operation. [. . . ] · Push only 1 appropriate digit key, [MONI 1(BANK)], [SCAN 2(T-SCAN)], [PRIO 3(PTT-M)], [HIGH 4(DTCS)] or [MID 5(DTCSS)] then push M [M(TONE-1)] or [SQLZ #(16KEY-L)] to select scan M edge channels. "M" and "#" can be used for "A" and "b" respectively. [M/CALL·PRIO] "!" appears w Rotate [DIAL] to select the desired memory channel. · Programmed memory channels only can be selected. 26 5 MEMORY OPERATION I Programming a memory channel VFO settings, including the set mode contents such as subaudible tone frequency or offset, can be programmed into a memory channel. w Push [S. MW·MW]. · "!" indicator and the memory channel number blink. eRotate [DIAL] to select the memory channel to be programmed. · Memory channels not yet programmed are blank. r Push [S. MW·MW] for 1 sec. to program. · 3 beeps sound · Memory channel number automatically increases when continuing to push [M/CALL·MW] after programming. CONVENIENT Memory programming can be performed in versatile ways e. g. memory channel to the same (or different) memory channel, memory channel to the call channel, etc. [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 (blank channel) via the controller. Push Rotate for setting frequency, etc. and continue to push " "Beep " Beep " Beep " 27 "Beep MEMORY OPERATION D Programming a memory channel via the microphone MW 5 The microphone can also be used to program memory channels. 3 beeps may sound and the VFO contents (including the subaudible tone frequency, etc. ) are programmed. Memory channel number increases when continuing to push [CLR A(MW)] after programming. z Set the desired frequency in VFO mode. offset frequency, duplex direction, subaudible tone encoder ON/OFF and its frequency), if necessary. · Direct numeral input cannot be used. 5 [EXAMPLE]: Programming 145. 870 MHz into memory channel 20 (blank channel) via the microphone. Push Push then "Beep Push 10 times Push then for 1 sec. and continue to push " "Beep " Beep " Beep " "Beep 28 5 MEMORY OPERATION I Copying memory contents This function copies a memory channel's contents to VFO (or another memory/call channel). This is useful when searching for signals around a memory channel frequency and for recalling the offset frequency, subaudible tone frequency etc. D Memory/callVFO q Select the desired memory or call channel. Push [M/CALL·PRIO] several times to select memory mode or call channel, then rotate [DIAL] or push [BAND] to select the desired memory or call channel respectively. to transfer the selected memory/call channel contents to the VFO. · VFO mode is selected automatically. MR/CALL MW [Y]/[Z] BAND z Select the memory/call channel to be transferred. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. to transfer the selected memory/call channel contents to the VFO. · VFO mode is selected automatically. [EXAMPLE]: Transferring memory channel 30 contents to VFO. Front panel operation: Push to select memory mode. Rotate for selecting memory channel. Push for 1 sec. HM-133 operation: Push to select memory mode. Push [Y]/[Z] to select memory channel. Push then push for 1 sec. 29 MEMORY OPERATION D Memory/callmemory/call q Select the memory/call channel to be transferred. Push [M/CALL·PRIO] several times to select memory mode or call channel, then rotate [DIAL] or push [BAND] to select the desired memory or call channel respectively. w Push [S. MW·MW] momentarily. · "!" indicator and "-- -- --" indication blink, and shows VFO conditions. 5 MR/CALL MW [Y]/[Z] z Select the memory/call channel to be transferred. Push [MR/CALL] to select memory mode, then select the desired memory channel via [Y]/[Z] or keypad. x Push [FUNC], then [CLR A(MW)] momentarily. · "!" indicator and "-- -- --" indication blink, and shows VFO conditions. 5 e Rotate [DIAL] to select the target memory channel. · "C1" or "C2" blinks when the call channel is selected. · Scan edge channels, 1A/1B, 2A/2B, 3A/3B, 4A/4B, 5A/5B can also be selected. BAND c Push [Y]/[Z] to select the target memory channel. · "C1" or "C2" blinks when the call channel is selected. [. . . ] Frequency cannot be set. · The frequency lock function is activated. 47 Frequency cannot be set · The frequency lock function is activated. 14 · Priority watch is paused on the watching fre- the microphone keypad lock function. 47 75 MAINTENANCE 12 -- PROBLEM POSSIBLE CAUSE SOLUTION REF. Some memory channels · The memory channel number has not yet been · Select the channel via the microphone keypad to cannot be selected via the programmed. [. . . ]