User manual HUSTLER 351254

[. . . ] Super Z Diesel Owner's Manual ······· Hustler Turf Equipment ····· P. O. Box 7000 ··· Hesston, Kansas · 67062-2097 351254_041505 WARNING: The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. 351254_041505 TABLE OF CONTENTS 1. General Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sect. Safety Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Sect. [. . . ] 4-2 Lubrication Grease the following areas per the Maintenance Schedule. Four deck lift pivots, located to the side of the operator's footrest 3. Blade spindle assemblies The spindle assemblies require lubrication annually. Each spindle shaft is equipped with a grease zerk located under the deck. Use no more than one or two ounces of SAE multipurpose grease, (1 to 2 pumps on an average grease gun). Bearings are sealed and do not require much lubricant. Wheel (lug) nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65-75 . . . . . . 88. 14-101. 7 Wheel motor nut . . . . . . . . . . . . . . . . . . . . . . . . . . . . 350-375 . . . . . 474. 6-508. 5 Blade spindle bolt top . . . . . . . . . . . . . . . . . . . . . . . . 65-75 . . . . . . 88. 14-101. 7 Blade spindle bolt bottom . . . . . . . . . . . . . . . . . . . . . 118 . . . . . . . . . . . . . . . . 160. 0 It is recommended that these be checked after the first 2 hours of operation, initially and every 50 hours following removal for repair or replacement. For all other torques refer to the tractor parts manual for standard torque chart. For engine torque values, see engine owner's manual. Tires It is important for level mowing that the tires have the same amount of air pressure. The recommended pressure are: Drive wheels. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-10psi (55-69 KPa) Gauge wheels. . . . . . . . . . . . . . . . . . . . . . . . . . 8-10 psi (55-69 KPa) Solid fill tires are not recommended for Hustler turf equipment. On any machine, with solid filled tires, the warranty claim will be denied. WARNING: Explosive separation of a tire and rim can cause serious injury or death. Do not attempt to mount a tire without the proper equipment and experience to perform the task. Never weld or heat a wheel and tire assembly as an explosion may occur. When inflating tires stand to one side and not in front of or over the tire assembly. Check tires for low pressure, blemishes, damaged rims or missing lug bolts and nuts. Electrical system The electrical system is a 12 volt, negative ground. Recommended battery size is a garden tractor BCI group U1R with 225 or better cranking AMP rating. Otherwise, follow battery manufacturer's maintenance, safety, storing and charging specifications. 4-3 WARNING: Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to cause cancer and reproductive harm. Always wear eye protection when checking the battery, acid can cause serious injury to skin and eyes. If contact occurs, flush area with clean water and call physician immediately. This gas is both toxic and flammable and may cause an explosion if exposed to flame. Use soda mixed in water to clean corrosion off the terminals. Hour meter Figure 4-2 4-4 351254_041505 Seat platform catch Battery Seat platform Figure 4-4 Hydraulic reservoir Figure 4-3 WARNING: Shorts caused by battery terminals or metal tools touching metal tractor components can cause sparks. [. . . ] Torque Caterpillar 34 3 91 CU IN (1490 CC) 22. 5:1 70. 8 FT LBS @ 1800 RPM Starter 12-volt (. 8 KW), solenoid shift positive engagement. Transmission drive (oil) cooler Pumps Hydrogear BDP21 Two variable displacement, axial piston type. Ground Speed - infinitely variable Transport 0-15 MPH (0-22. 53 KPH) forward Mowing 0-10 MPH (0-16. 09 KPH) forward and 0-7. 5 MPH (0-12. 07 KPH) reverse Steering Twin lever steering provides independent control of each drive wheel. Speed, forward, reverse, brake, and turns are all controlled with hand operated controls. [. . . ]