Detailed instructions for use are in the User's Guide.
[. . . ] It should be read and used by any person installing or using the machine. The obligatory technical regulations in force in the country where the machine is used must also be adhered to for maximum safety. The use of symbols on machines (in color) and in the manual identify advice concerning your safety. OBLIGATIONxxxxBlue background, white marking : obligatory safety OBLIGATIONxxxx+ red marking : movement forbidden WARNINGxxxxBlack triangle and marking on a yellow background : danger if not adhered to. [. . . ] PROHIBITIONxxxx Red circle with or without bar : use or presence prohibited. INFORMATIONxxxxInformation - Instruction: special instructions concerning use and inspection. The manufacturer declines any responsibility resulting from improper use, or modifications. This symbol indicates that the machine is in conformance with the applicable European directive. The disc cutter is designed to provide safe and reliable service in operating conditions corresponding with the instructions, but it can present dangers for the user and risks of damage, consequently regular on site inspection is necessary to ensure : · Perfect technical condition (use for the purpose for which it is intended and taking into account any risks, and correction of any malfunction detrimental to safety). Use of a diamond disc for water lubricated cutting of marble, stone, granite, brick and facings (porcelain, glazed tiles, ceramics, etc). Competent personnel (qualifications, age, training, education) who have studied the manual in detail before starting work: any fault of an electrical or other nature must be checked by a competent person (electrician, maintenance foreman, authorized dealer, etc). That the warnings and instructions marked on the machine are followed (adequate personal protection, correct use, general safety instructions, etc). That no modification, transformation or addition is detrimental to safety and that it is carried out without prior authorization from the manufacturer. Do not use the saw for any purpose for which it is not designed (using a saw blade or abrasive disk which do not conform to the instructions for use). - Extension lead : Cable size sufficient for the electrical power, connection to the mains by a H07 RNF type cable of the following size : - 3 x 2. - Make sure that the supply is correctly plugged in (plug, extension lead, etc) - Check the supply cable - Test or have tested by an electrician (circuit breaker, plug, etc) - Have tested by an electrician or contact the service department - Contact the service department to have the motor replaced Before carrying out any operation disconnect the machine from the mains Empty regularly the tank to remove muddy deposits which could clog the pump and thus cause premature wear. Single phase motor starting condenser Store in a dry place, not accessible to children. The mains lead is not correctly connected or is damaged No voltage in pump circuit or mains supply circuit An air bubble may have - Holding the pump of formed inside the pump the outlet pipe remove body it from the water and reimmerse it The turbine is jammed - Unscrew the filter and, using a small screwdriver, remove all dirt from the operating area of the turbine. Contact your supplier who is entirely at your service to carry out repairs in the shortest time at the best possible price. This adjustment is necessary only if the wheels (D) no longer bear on the rail (R). Loosen the 2 nuts (A), opposite side of the disc using a N° 13 wrench, then tighten the screws (C) using a N° 6 wrench (not supplied) · For rapid delivery of spares and in order to avoid any wasted time, it is necessary to remind your supplier of the details shown on the instruction plate on the machine with each order, as well as the reference of the part to be replaced. Position the extension to the left, or the right, to ensure maximum stability when cutting large size materials. The manufacturer declines all responsibility for loss or damage resulting from misuse or any modification, alteration or powering that does not conform to the manufacturer's original specifications. At the work station, the sound pressure level may exceed 85 db (A) In this case individual protection measures must be taken. [. . . ] At the work station, the sound pressure level may exceed 85 db (A) In this case individual protection measures must be taken. In the event of deterioration and scrapping of the machine, the following items must be disposed of in accordance with the requirements of the legislation in force. The instructions for use and spare parts found in this document are for information only and are not binding. As part of our product quality improvement policy, we reserve the right to make any and all technical modifications without prior notice. [. . . ]