User manual HUSQVARNA TS 400 F

[. . . ] Following the instructions will ensure that your machine gives long service, in normal operating conditions. The user advice and spare parts mentioned in this document are given as an indication, and do not constitute an undertaking. No warrantee will be granted in the event of errors or omissions, or for damage occurring during delivery, or caused by the design or use of the machine. We are very concerned about the quality of our products and we reserve the right to make any technical modifications to improve them, without warning. [. . . ] Use of a diamond disc for water lubricated cutting of marble, stone, granite, brick and facings (porcelain, glazed tiles, ceramics, etc). Competent personnel (qualifications, age, training, education) who have studied the manual in detail before starting work: any fault of an electrical or other nature must be checked by a competent person (electrician, maintenance foreman, authorized dealer, etc). That the warnings and instructions marked on the machine are followed (adequate personal protection, correct use, general safety instructions, etc). That no modification, transformation or addition is detrimental to safety and that it is carried out without prior authorization from the manufacturer. Any application not corresponding with the intended use (use of a saw blade, abrasive disc, etc) is prohibited. Use : Sawing marble, stone, granite, brick, cement and all facings (porcelain, glazed tiles, ceramics, etc). 1 PLACING ON FEET (SEE FIG 8) 1 Chassis-tank 2 Leg 3 Head clamping handle 4 Water pump 5 Handwheel height locking 6 Adjustment crank 7 Loading wheelst 8 Drain plug 9 Motor 10 Lack of voltage switch 11 Hood 12 Disc casing 13 Housing cover 14 Movable table 15 Table stop 16 Movable table stop 17 Manufacturer's plate 18 Cutting guide 19 Table locking 20 Carrying handles 21 Transport wheels 22 Settling tank 23 Water level 4 Handling - transport Inspection before starting Please read the instructions for use prior to operating the machine for the first time. The working area must be completely cleared, well lit and all safety hazards removed (no water or dangerous objects in the vicinity). Use blades suitable for the work to be done (speed, geometry, application, etc. The operator must wear protective clothing appropriate to the work he is doing. - Use the following types of plug, single phase 2 P + E, or 3xPx+xE / 3xPx+xNx+xE according to the corresponding voltage. - Extension lead: Cable size sufficient for the electrical power, connection to the mains by a H07 RNF type cable of the following size: - 3 x 2. If the machine is fitted with a brake motor, do not use the quick-tightening nut. Take care about the direction of rotation which is shown by an arrow on one of the faces. Make sure the contact faces of flanges, of blade and the axle are clean. Starting up Always pay extreme care and attention to the preparation of the machine before starting up Remove all adjustment tools and wrenches from floor and machine Always keep blade guard in place Electrical connection - ELECTRICAL SAFETY : Operate this machine only on a supply equipped with a 30 mA earthed current-limiting circuit-breaker. For tools supplied with an integral RCCB in the cable or in the mains plug, if the cable or plug has been damaged, repairs must be carried out by the manufacturer, one of his agents or by a qualified repair workshop to avoid any risks resulting from errors. As each machine is fitted with a self priming pump, the water is sprayed onto the disc as soon as the machine starts. [. . . ] For rapid delivery of spares and in order to avoid any wasted time, it is necessary to remind your supplier of the details shown on the instruction plate on the machine with each order, as well as the reference of the part to be replaced. In the event of a long period of use pay special attention to the maintenance and protection of the disc. Make sure that the contact faces of the disc, the flanges and the spindle are clean. The manufacturer declines all responsibility for loss or damage resulting from misuse or any modification, alteration or powering that does not conform to the manufacturer's original specifications. [. . . ]