User manual HUSQVARNA SNOW THROWER SNÖSLUNGA LUMILINKO SNØFRESER SCHNEESCHLEUDER T-40212 531 02 06-04

[. . . ] Never put your foot or hand in the auger or in the discharge chute when the snow thrower is running. [. . . ] If the unit should start to vibrate abnormally, stop the engine and check immediately for the cause. Take all possible precaution when leaving the vehicle unattended, disengage the power take-off, lower the attachment, shift into neutral, set the parking brake, stop the engine, remove the key. Never operate snow thrower without guards, plates or other safety protective devices in place. Never direct discharge at bystanders or allow anyone in front of unit. For best efficiency, clear snow before it melts, refreezes and hardens. Do not overload machine capacity by attempting to clear snow at too fast rate. [. . . ] Pos Part number 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 531 02 11-01 531 02 11-02 531 00 52-52 531 00 52-53 531 00 52-54 531 00 52-55 531 00 52-56 531 02 11-25 531 02 11-04 531 00 52-21 531 00 52-59 531 00 52-60 531 02 11-38 531 00 51-98 531 02 11-39 531 00 51-97 531 00 52-62 531 00 52-63 531 00 51-92 531 00 52-16 531 00 52-17 531 02 11-27 531 02 11-37 531 02 11-30 531 00 51-41 531 00 52-64 531 00 51-43 531 02 11-46 531 00 52-66 531 00 52-65 531 02 11-84 531 02 11-95 531 00 52-67 531 00 52-68 531 00 52-69 531 02 11-96 531 02 11-97 531 00 52-70 531 02 11-98 531 02 11-99 531 02 11-05 531 02 12-16 531 02 11-06 531 02 11-07 531 02 11-08 531 00 52-75 531 02 11-09 531 00 51-31 531 02 11-44 531 00 52-78 531 02 12-17 531 00 52-79 531 02 11-10 Part name Frame Weldment, Spiral Guard Skid Plate Drive Chain Joint Control Rod Weldment, Lift Weldment, Lift Shaft Bearing Collar Bearing Circlip Pulley Collar Pulley Collar Shaft Pin, Spring Pin Set Screw Washer Nut, Lock Grip Grip Pin, Spring Screw Screw, Lock Collar Washer Screw, Special Discharge Pipe Chute Rubber Screw Washer Screw, Special Nut, Lock Screw Collar Washer Belt Guard Weldment Guard Pulley Drive Shaft V-Belt Screw Key Set Screw Weldment Support, Lift Qty 1 1 1 2 1 1 1 1 1 1 4 1 8 2 1 1 1 1 1 5 3 1 6 5 1 1 3 17 6 1 36 2 1 1 1 2 2 2 2 5 5 5 1 1 1 1 1 1 14 1 2 1 1 Pos Part number 55 56 57 58 59 60 61 62 63 65 66 67 68 69 70 71 74 76 77 78 79 80 81 82 83 84 85 86 87 88 531 02 11-28 531 02 12-73 531 00 52-83 531 02 12-18 531 02 11-48 531 02 11-42 531 00 52-85 531 00 52-86 531 00 52-87 531 00 52-89 531 00 52-90 531 00 52-91 531 02 11-40 531 00 52-80 531 00 52-03 531 00 52-93 531 02 11-12 531 02 12-19 531 02 11-13 531 02 12-20 531 02 11-81 531 02 11-82 531 02 11-83 531 00 52-61 531 02 12-23 531 02 12-45 531 02 12-46 531 02 11-72 531 02 12-68 531 02 12-70 Part name Screw Frame Support Pin Nut, Lock Nut Guide, Belt Collar Collar Collar Collar Screw, Lock Screw Belt Tightener Spring Plate Lever Nut, Lock Slide Ring Pin Limiter Plate Side Plate, Left Side Plate, Right Pulley Support Mounting Plate Mounting Plate Screw (carriage bolt Spring Kit for cable clutch Qty 2 1 1 1 2 1 2 2 2 1 1 1 1 1 1 1 1 28 1 1 1 1 1 2 1 1 1 2 1 0 VANNE, KOVA, Veistämöntie 16, FIN-24800 HALIKKO, FINLAND, hereby certifies that the machine of type T-40212 conforms to Machine Directive 89/392/EEC, 91/368/EEC, 93/44/EEC with special reference to Annexe 1 of the directive concerning essential health and safety requirements in relation to design and manufacture. [. . . ]