User manual HUSQVARNA RZ3016

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA RZ3016. We hope that this HUSQVARNA RZ3016 user guide will be useful to you.


HUSQVARNA RZ3016 : Download the complete user guide (3704 Ko)

Manual abstract: user guide HUSQVARNA RZ3016

Detailed instructions for use are in the User's Guide.

[. . . ] Operator Manual Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. RZ3016 / 966042901 RZ3016BF / 966495501 In order to implement improvements, specifications and designs can be altered without prior notification. Note that no legal demands can be placed based on the information contained in these instructions. Do not modify or install non-standard equipment to the unit without consent from the manufacturer. Modifications to the unit may cause unsafe operations or damage the unit. ©2009 Husqvarna. [. . . ] Make sure the fuel caps are properly tightened and the cap gasket is not damaged. The engine will run on a minimum of 85-octane unleaded gasoline (no oil mix). Damage to engine and components may occur. IMPORTANT INFORMATION Experience indicates that alcohol blended fuels (called gasohol, ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Drain the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. Never use engine or carburetor cleaners in the fuel tank or permanent damage may occur. Fuel tank 8050-012 WARNING!Allow engine and exhaust system to cool at least two (2) minutes before refueling WARNING!Do not store, spill or use gasoline near an open flame. 20 - HUSQVARNA CONTROLS Fuel Shut Off Valve The fuel shut off valve is located in the fuel line under the seat. Rotate the valve ¼ turn clockwise to turn fuel OFF. IMPORTANT INFORMATION In order to obtain an even cutting height, it is important that the air pressure is 15 psi in all tires. Fuel shut off valve in the OPEN position. 8050-010 Mower Deck Lifting Lever The lifting lever is used to place the mower deck in the transport position or one of the 6 different cutting height positions. The cutting height is set by placing a lever in the notch for the desired cutting height. The lifting lever can also be used to temporarily adjust the cutting height, such as when passing a minor bump in the lawn. IMPORTANT INFORMATION Always use the high position (F) to transport. The mower deck’s lifting lever 8050-014 Tracking If the mower is not tracking straight, check the air pressure in both rear tires. (1 bar) Tracking must be checked on a flat and level concrete or blacktop surface. If the unit still does not track straight contact your Husqvarna workshop for adjustments. HUSQVARNA-21 CONTROLS Blade Control Lever To lower the mower deck and engage the blades, lift the lever up off the lock notch and lower slowly. WARNING!No adjustments or maintenance to be carried out unless: ♦ the engine stopped ♦ the ignition key removed ♦ the parking brake activated Manual Transport Mower deck blade control lever in the disengaged position 8050-016 When pushing or pulling the mower, be sure to engage the EZT Hydrogear bypass linkages. The EZT bypass linkages are located on the rear of the frame, below the rear engine guard. • To reengage the EZT’s to drive, reverse the above procedure. Set bypass linkages into slots on both sides 8050-018 22 - HUSQVARNA operation Read “Safety Instructions” section and following pages, if you are unfamiliar with the machine. Steering To move forward and backward The direction and speed of the mower’s movements is effected by the movement of the control lever(s) on each side of mower. First time users should push mower (see “Moving by Hand” in the Operation section) to an open, flat area, without other people or vehicles/obstacles nearby. In order to move unit under its own power, the operator must be in the seat, start engine (see “Before Starting” in Operation section), adjust engine speed to idle, disengage parking brake, do not engage blades at this time, rotate control levers inward. As long as the control levers have not been moved forward or backwards, mower will not move. Pull back on control levers to the neutral position and mower should stop moving. Pull back slightly on control levers, this will allow mower to start moving backwards. [. . . ] Start the engine and allow it to run until the carburetor is drained of fuel or the stabilizer has reached the carburetor. 5. Remove the spark plug and pour about a tablespoon of engine oil into the cylinder. Turn over the engine so that the oil is evenly distributed and then refit the spark plug. Clean, charge, and store the battery in a cool place, but protect it from direct cold. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA RZ3016




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA RZ3016 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.