User manual HUSQVARNA RIDER 1200-18

[. . . ] Prevent accidents due to unsuitable use, by an untrained person, during maintenance, repairs, overhauls, handling or transport · improve the reliability and durability of the machine · Ensure correct use, regular maintenance, and fast fault finding in order to reduce repair costs and downtime. It should be read and used by any person installing or using the machine. The obligatory technical regulations in force in the country where the machine is used must also be adhered to for maximum safety. GENERAL SAFETY INSTRUCTIONS The use of symbols on machines (in color) and in the manual identify advice concerning your safety. [. . . ] That the warnings and instructions marked on the machine are followed (adequate personal protection, correct use, general safety instructions, etc). That no modification, transformation or addition is detrimental to safety and that it is carried out without prior authorization from the manufacturer. Electrical connection - ELECTRICAL SAFETY : Operate this machine only on a supply equipped with a 30 mA earthed current-limiting circuitbreaker. Hands should be placed on the front hub (A) and at the back of the machine (B). - Make sure that the mains voltage corresponds with that marked on the manufacturer's plate on the machine. - Three-phase motor: Ensure that the direction of rotation matches the direction of the arrow marked on the motor cover: if the motor does not turn in the desired direction, reverse the two power supply wires: - Use single-phase plugs of the 2P + E type or three-phase plugs of the 3P + N + E type, depending on the voltage concerned. Please read the instructions for use prior to operating the machine for the first time. The working area must be completely cleared, well lit and all safety hazards removed (no water or dangerous objects in the vicinity). The operator must wear protective clothing appropriate to the work he is doing. We recommend that this includes both eye and ear protection Any persons not involved in the work should leave the working area. Plates having a shape, size or mounting method which does not suit the machine must never be used. Floor in the form of "MACHINED" or "RUBBLE" rock The opus may be either stone or marble, the joints are usually in granito, i. Crushed marble mixed with cement and colorant, the joints must stand proud by a few millimetres and for this reason a Bakelite rough stone block crown wheel with a granular size of 16 Q must be used. After this slip has dried, which takes 24 hours in a normally heated room or 15 to 30 minutes in the case of STONIX mastic. POLISHING This is done successively with magnesia segments with a respective granular size of 2, 3 and 4 (5 Star Super to obtain a brilliant satin finish). the successive operations using these different granular sizes enable the polishing marks gradually to be reduced and eliminated to obtain a perfect finish. IMPORTANT: It would be wrong to avoid using one of these successive granular sizes to make the operation cheaper because this would not in fact be the case since by missing out, for instance, granular size 2 and going directly to 3, twice the time must be spent to obtain an identical result. Each granular size has been designed to obtain the finish required and the stipulated method of operation must be followed scrupulously. After polishing with granular size 4, it can be agreed that the polishing is perfect and that the operation is complete: you now have paving with no ridges but which still lacks the liveliness of brilliantly polished stone. Your polishing machine is fitted with a felt support plate and a polishing felt of very hard quality to ensure a constantly even finish. For light marbles and stone: you simply use a felt with no other accessory after ensuring that the paving is perfectly clean and dry. Add a few drops of water to the powder on the surface to be polished to form a paste and pass the felt support plate over this mixture. [. . . ] Each time, when you have finished using the machine, close the water tap. If you will not be using the machine for a certain length of time, take care to remove the tank by removing the two screws at the front, on the base of the tank and one screw situated above the motor. Type A Type C Type D For marble and light stone For dark marble and granite Universal We recommend that you refer to the instructions for using our POLYECLAIR product, which will provide total satisfaction and very satisfactory performance. The machine must not be started in vertical position or when it is raised Designed to compensate for more regular wear of the segment blocks or abrasives. [. . . ]