User manual HUSQVARNA JET 49

[. . . ] WARNING: Battery posts, terminals and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Wash hands after handling. SAFETY RULES • • • • • • • • • Stop the blade(s) when crossing gravel drives, walks, or roads. Stop the engine (motor) whenever you leave the equipment, before cleaning the mower or unclogging the chute. Shut the engine (motor) off and wait until the blade comes to complete stop before removing grass catcher. [. . . ] For extremely heavy cutting, reduce the width of cut by overlapping previously cut path and mow slowly. For better grass bagging and most cutting conditions, the engine speed should be set in the FAST position. Pores in cloth grass catchers can become filled with dirt and dust with use and catchers will collect less grass. To prevent this, regularly hose catcher off with water and let dry before using. Keep top of engine around starter clear and clean of grass clippings and chaff. This will help engine air flow and extend engine life. • PRIMER FIG. Use fresh, clean, regular unleaded gasoline with a minimum of 87 octane. Purchase fuel in quantities that can be used within 30 days to assure fuel freshness. Alcohol blended fuels (called gasohol or using ethanol or methanol) can attract moisture which leads to separation and formation of acids during storage. To avoid engine problems, the fuel system should be emptied before storage of 30 days or longer. Empty the gas tank, start the engine and let it run until the fuel lines and carburetor are empty. • At least once a year, replace the spark plug, clean or replace air filter element and check blade for wear. A new spark plug and clean/new air filter element assure proper air-fuel mixture and help your engine run better and last longer. • Follow the maintenance schedule in this manual. LUBRICATION CHART WHEEL ADJUSTER (ON EACH WHEEL) ➀ ➁ ENGINE OIL ➀ MULCHER DOOR HINGE PIN ➀ REAR DOOR HINGE BEFORE EACH USE 1. Check for loose fasteners. LUBRICATION Keep unit well lubricated (See “LUBRICATION CHART”). IMPORTANT: DO NOT OIL OR GREASE PLASTIC WHEEL BEARINGS. VISCOUS LUBRICANTS WILL ATTRACT DUST AND DIRT THAT WILL SHORTEN THE LIFE OF THE SELFLUBRICATING BEARINGS. IF YOU FEEL THEY MUST BE LUBRICATED, USE ONLY A DRY, POWDERED GRAPHITE TYPE LUBRICANT SPARINGLY. ➀ HANDLE BRACKET MOUNTING PINS ➀ SPRAY LUBRICANT 9 ➁ SEE “ENGINE” IN MAINTENANCE SECTION MAINTENANCE LAWN MOWER Always observe safety rules when performing maintenance. • • TIRES • • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. The blade can be sharpened with a file or on a grinding wheel. If either end of the blade moves downward, sharpen the heavy end until the blade is balanced. BLADE ADAPTER BLADE LOCK WASHER KEY CRANKSHAFT KEYWAY BLADE CARE For best results, mower blade must be kept sharp. CAUTION: Use only a replacement blade approved by the manufacturer of your mower. Using a blade not approved by the manufacturer of your mower is hazardous, could damage your mower and void your warranty. [. . . ] 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 --PART NO. 532 15 03-48 532 16 43-62 532 08 39-23 532 18 88-13 532 08 86-52 532 16 57-66 532 16 57-67 532 18 58-19 532 15 04-06 532 10 73-39 873 80 05-00 532 16 86-02 532 18 05-52 532 19 47-15 532 14 72-86 532 16 36-62 532 85 10-84 532 85 02-63 532 85 10-74 532 18 90-28 532 19 37-07 532 18 88-21 --532 18 06-26 532 19 18-53 873 80 04-00 532 19 34-98 532 19 36-96 532 08 83-48 532 18 81-52 532 19 27-70 532 18 63-62 532 16 23-00 532 19 69-55 DESCRIPTION Wheel & Tire Assembly, Front 8 x 2 Shoulder Bolt Nut, Hex, Flangelock Frame, Grassbag Hinge Screw Spring, Rear Door, LH Spring, Rear Door, RH Rod, Rear Door Hex Head Thread Rolling Screw 3/8-16 x 1 Danger Decal Nut, Hex Axle Arm Assembly, Rear, RH Wheel & Tire Assembly, Rear 14 x 2 Grassbag Hinge Rod Kit, Lawn Mower Housing Assembly (Includes Key Numbers 17, 18 and 46) Hex Head Screw 3/8-24 x 1-3/8 Grade 8 Helical Lockwasher Hardened Washer 21" Blade Blade Adapter Adjustment Bolt Engine, Briggs & Stratton, Model Number 12H602 (Order parts from engine manufacturer) Hubcap, Front Wheel, 8" Hubcap, Rear Wheel, 3" Nut, Hex, Nylock 1/4-20 Kit, Bushing, High Wheel Bushing, Nylon, Black Washer, Flat O-Ring Clip, Cable Grip, Foam Warning Decal (not shown) Owner’s Manual, English / French 17 NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty. WARRANTY STATEMENT SECTION 1: LIMITED WARRANTY Husqvarna Forest & Garden Company (“Husqvarna”) warrants Husqvarna product to the original purchaser to be free from defects in material and workmanship from the date of purchase for the “Warranty Period” of the product as set forth below: Lifetime Warranty: All tiller tines against breakage, trimmer shafts, ignition coils and modules on hand held product. [. . . ]