User manual HUSQVARNA GTH26V52LS

[. . . ] 07002 GTH26V52LS Owner's Manual Gasoline containing up to 10% ethanol (E10) is acceptable for use in this machine. The use of any gasoline exceeding 10% ethanol (E10) will void the product warranty. 532 44 46-96 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. [. . . ] 16 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. NOTE: The original equipment battery on your tractor is maintenance free. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Clean terminals and battery cable ends with wire brush until bright. • Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). 02828 ROS "ON" POSITION ENGINE "ON" POSITION (NORMAL OPERATING) Fig. 15 15 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. CAUTION: Remove lower dash cover carefully to ensure cover tabs are not broken. LOWER DASH COVER TRANSAXLE MAINTENANCE The transmission fan and cooling fins should be kept clean to ensure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transmission. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. FASTENER SLOTS TABS Fig. 18 • • • • Slide lower dash cover up to release cover tabs from tapered slots in lower dash and remove. Open drain valve by using a 10mm wrench turning counterclockwise. OIL DRAIN VALVE TO OPEN TO CLOSE 02 79 4 TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 DRAIN TUBE Fig. 19 • • • • After oil has drained completely, close the drain valve turning clockwise. Use the 10mm wrench to apply a small amount of torque to keep it closed. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual. ” Tighten cap onto the tube securely when finished. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE Fig. [. . . ] 960 43 01-18 MOWER DECK 52 33 17 24 53 57 18 19 31 30 47 25 34 43 45 46 56 16 27 33 24 15 35 44 59 16 37 39 38 61 36 1 23 22 51 50 6 55 3 32 5 4 21 54 20 62 63 58 2 60 8 9 29 28 10 11 13 14 7 12 52F-tex_elec_5 40 TRACTOR - MODEL NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 27 28 29 30 31 32 PART NO. 575 43 80-03 539 11 21-70 532 18 76-90 532 10 75-21 532 40 02-34 539 10 76-30 532 11 07-33 532 11 07-35 532 11 07-36 574 87 08-01 539 10 75-22 574 87 50-02 539 99 07-99 539 99 07-17 532 19 51-61 539 11 28-99 532 19 61-04 574 84 18-02 532 17 79-68 539 13 27-28 575 22 45-01 539 10 76-10 539 19 34-06 521 99 65-01 575 22 47-02 539 10 47-63 539 10 82-71 539 10 65-04 539 99 05-17 539 97 69-79 539 99 09-23 DESCRIPTION Deck w/ Decals 52" Housing Assembly Washer-Spacer Pulley, Mandrel Nut, 9/16 Top Center Lock Screw, Washer Head Discharge Chute, 52" Spring - Torsion Pin, Clevis 5/16 x 5. 19 Blade, 16-1/4" Bolt, 7/16, Assy Blade Confinement Plate Rhsnb 5/16-18 x 5/8 Gr 5 Nut 5/16-18 Hex Nyloc Stud, Fasten w/ Anti- Rotate Nut 5/16-18 Hex Flange Nyloc Pulley, Idler Spec. Hub Arm, Idler, Blk Pulley, Idler Pulley, Idler Idler Bushing Wheel, Gauge Bolt, Shoulder Nut 3/8-16 Hex Flg Nyloc Shield, Belt LH Retainer 5/16c U Type Hcs 3/8-16 x 3-1/2 Gr 5 Heavy Washer Washer, 3/8 Flat Std Nut 3/8-16 Hex Nyloc Rhsnb 3/8-16 x 1-3/4 Gr 5 KEY NO. [. . . ]