User manual HUSQVARNA GTH 2250 A

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA GTH 2250 A. We hope that this HUSQVARNA GTH 2250 A user guide will be useful to you.


HUSQVARNA GTH 2250 A : Download the complete user guide (1932 Ko)

Manual abstract: user guide HUSQVARNA GTH 2250 A

Detailed instructions for use are in the User's Guide.

[. . . ] GTH2250 Owner’s Manual SAFETY RULES SAFE OPERATION PRACTICES FOR RIDE-ON MOWERS IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. GENERAL OPERATION • • • • • • • • • • • • • • • • Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. [. . . ] Replace belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF-SJ. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 F C -30 -20 -20 0 -10 30 32 0 40 10 60 20 80 30 100 40 TO CHANGE ENGINE OIL (See Fig. • Remove cap from bottom fitting of drain valve and install the drain tube onto the fitting. • Unlock drain valve by pushing inward and turning counterclockwise. • After oil has drained completely, close and lock the drain valve by pushing inward and turning clockwise until the pin is in the locked position as shown. • Remove the drain tube and replace the cap onto to the bottom fitting of the drain valve. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual. Keep oil at “FULL” line on dipstick. OIL DRAIN VALVE CAP CLOSED AND LOCKED POSITION TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE FIG. 16 NOTE: Although multi-viscosity oils (5W30, 10W30 etc. ) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/ dipstick securely each time you check the oil level. DRAIN TUBE FIG. 17 CLEAN AIR SCREEN Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. CLEAN AIR INTAKE/COOLING AREAS To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times. Every 100 hours of operation (more often under extremely dusty, dirty conditions), remove the blower housing and other cooling shrouds. [. . . ] 532137200 532137729 532136574 532137272 532137273 532139245 532137789 532139573 532144959 532138687 532133957 532137644 532133943 872110612 819121414 532151831 532173979 873930600 874780516 532175746 532175747 819171416 532132264 872110614 532155986 532156941 532156852 532156853 532156854 532156856 872010505 873980500 819171216 872110504 532153183 532143651 532178346 DESCRIPTION Cover, Mandrel RH Screw, Thd Roll 1/4-20 x 5/8 Cover, Mandrel LH Arm, Idler Primary Spring, Secondary Pulley, Idler V Groove Shield, Idler V-Belt, Mower Primary V-Belt, Mower Secondary Spring, Primary Wheel, Gauge Bolt, Shoulder Washer Hardened Bolt Carriage 3/8-16 x 1-1/2 Washer 3/8 x 7/8 x 14 Ga. Pulley Idler Flat Mower Keeper, Belt Idler 50" Vent Nut, Center Lock 3/8-16 Bolt H 5/16-18 x 1 Bracket, Asm. Pin Head Rivot Bracket Ga Wh Asm RH 50 Bracket Ga Wh Asm LH 50 Bracket Ga Wh Assy F RH 50 Bracket Ga Wh Assy F LH 50 Bolt Carraige 5/16- 18 x 5/8 Nut Crownlock 5/16-18 Washer 17/32 x 3/4 x 16 Ga. Bolt Carriage 5/16-Unc 1/2 Reinforcement Mandrel Ring Mandrel Asm (Includes Key Nos. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA GTH 2250 A




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA GTH 2250 A will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.