User manual HUSQVARNA FT900

[. . . ] FT900 Owner's Manual "This machine is approved by the EPA for E10 (10% ethanol) and lower fuel only. Do not use any fuel >E10 in this machine. " 532 43 99-99 SAFETY RULES Safe Operation Practices for Walk-Behind Powered Rotary Tillers TRAINING • • • • • • • • • • Read the Owner’s Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Never allow adults to operate the equipment without proper instruction. [. . . ] See “TINE OPERATION CHECK” in the Service and Adjustments section of this manual. 4 5 3 6 2 7 1 TILLING HINTS CAUTION: Until you are accustomed to handling your tiller, start actual field use with throttle in slow position. To help tiller move forward, lift up the handles slightly (thus lifting depth stake out of ground). If you are straining or tiller is shaking, the wheels and depth stake are not set properly in the soil being tilled. The proper setting of the wheels and depth stake is through trial and error and depends upon the soil condition. (The harder or wetter the ground, the slower the engine and tine speed needed. Under these poor conditions, at fast speed the tiller will run and jump over the ground). A properly adjusted tiller will dig with little effort from the operator. • Tilling is digging into, turning over, and breaking up packed soil before planting. Depending on the climate (rainfall and wind), it may be advisable to till the soil at the end of the growing season to further condition the soil. Fig. 9 CULTIVATING Cultivating is destroying the weeds between rows to prevent them from robbing nourishment and moisture from the plants. At the same time, breaking up the upper layer of soil crust will help retain moisture in the soil. Begin by tipping the depth stake forward until it is held by the stake spring. • Cultivate up and down the rows at a speed which will allow tines to uproot weeds and leave the ground in rough condition, promoting no further growth of weeds and grass (See Fig. 10 MAINTENANCE BE FO RE EA EV CH ER US Y5 E HO EV ER UR Y2 S 5H EV OU ER RS Y5 0H OU RS MAINTENANCE SCHEDULE FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Engine Oil Level Change Engine Oil Oil Pivot Points Inspect Spark Arrester / Muffler Inspect Air Screen Clean or Replace Air Cleaner Cartridge Clean Engine Cylinder Fins Replace Spark Plug SERVICE DATES 1, 2 2 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. GENERAL RECOMMENDATIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain tiller as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your tiller. All adjustments in the Service and Adjustments section of this manual should be checked at least once each season. • Once a year you should replace the spark plug, clean or replace air filter, and check tines and belt for wear. A new spark plug and clean air filter assure proper air-fuel mixture and help your engine run better and last longer. LUBRICATION CHART  TINE CONTROL  ENGINE BEFORE EACH USE • • • Check engine oil level.  IDLER ARM LUBRICATION Keep unit well lubricated (See “LUBRICATION CHART”) . SAE 30 OR 10W-30 MOTOR OIL REFER TO MAINTENANCE “ENGINE” SECTION 10 MAINTENANCE Disconnect spark plug wire before performing any maintenance (except carburetor adjustment) to prevent accidental starting of engine. Do not touch hot muffler or cylinder fins as contact may cause burns. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classification SG-SL. [. . . ] Make necessary adjustments. Soil balls up or clumps Engine runs but tiller won’t move Engine runs but labors when tilling 17 REPAIR PARTS HANDLE ASSEMBLY 3 16 TILLER - MODEL NO. 960 83 00-05 1 19 2 3 29 19 4 29 20 5 6 10 11 20 7 14 7 8 9 12 13 FT-handle_assy_5 KEY NO. 532 44 07-18 872 14 05-12 532 16 57-87 532 44 07-14 873 68 05-00 819 11 11-16 819 12 14-14 874 76 05-20 874 76 05-16 810 04 05-00 873 22 05-00 DESCRIPTION Panel, Control Bolt, RDHD 5/16-18 x 1 1/2 Grip, Handle Handle, LH Double Bend Nut, Crown Lock 5/16 -18 Washer 11/32 x 11/16 x 16 Ga. Bolt Fin Hx 5/16-18 x 1. 25 Bolt Hex Hd 5/16-18 x 1 Washer Lock 5/16 Nut, FIn Hx 5/16-18 KEY NO. [. . . ]