User manual HUSQVARNA FS 6600 D

[. . . ] Operator's manual Please read the operator's manual carefully and make sure you understand the instructions before using the machine. Husqvarna AB, SE-433 81 Göteborg, Sweden, tel: +46-31-949000, declares under sole responsibility that the Husqvarna FS 6600 D, FS 8400 D dating from 2010 serial numbers and onwards (the year is clearly stated on the rating plate, followed by the serial number), complies with the requirements of the COUNCILíS DIRECTIVE: · DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO DO 8 Read this entire operator's manual before operating this machine. Keep all parts of your body away from the blade and all other moving parts. Shut off the engine and allow it to cool before refueling or doing maintenance. [. . . ] Always use Lockwasher (2J) with bladeshaft Bolt (2A) Replace Bolt (2A) and Lockwasher (2J) when worn or damaged. Slip on blade guards are provided with a safety latch which engages the support spade and a bolt to retain the rear of the guard. Do not operate this saw without the latch engaged and the bolt installed. Take into account the working conditions from health and safety point of view. Slip the Blade Shaft Wrench between the guard and the belt guard onto the latch lever. to Install A SLIP-ON GUARD: · Lower guard onto spade until latch engages. Move the saw forward or reverse slowly by pushing or pulling on the Speed Control Lever (1M). Make sure the Front Guide (6D), Rear Guide (6F) and Diamond Blade (2E) stay on the line. Lower the saw by pressing the Raise/ Lower Switch (1N) on the Speed Control Lever (1M) downward until the Diamond Blade (2E) is at the desired cutting depth (See "Blade Cutting Depth Information"). Blade Cutting Depth Information: The saw is equipped with a BLADE DEPTH INDICATOR (1O) which has two number ranges. The Orange and White number ranges are used for two different purposes: 1) The "Depth" number range, indicated by the Orange color, shows the current Cutting Depth of the DIAMOND BLADE (2E). As the saw is lowered, the BLADE DEPTH INDICATOR (1O) needle travels through these numbers in increasing order. It can be used with or without the BLADE DEPTH STOP SWITCH (1K) feature. As the saw is lowered, the BLADE DEPTH INDICATOR (1O) needle travels through the White color number range in decreasing order, indicating the unfinished depth of cut. when the BLADE DEPTH INDICATOR (1O) needle reaches "0" position , the desired maximum cutting depth is reached. If the BLADE DEPTH STOP SWITCH (1K) feature is used ("1" or "ON" position), the lowering process stops automatically. Using the BLADE DEPTH INDICATOR (1O): "Depth" Mode (Orange colored numbers show current cutting depth): · Turn ENGINE START SWITCH (1C) to "0" (OFF) position to STOP engine (If running). Turn ENGINE START SWITCH (1C) to "1" (RUN) position to power electrical system. Search for FS6600 FS8400 Display and Electronics Manual Always pay extreme care and attention to the preparation of the machine before starting. Follow all operating instructions and warnings in this manual and on the machine. Mark the surface to be cut by drawing a line where the cut is to be made. Lower the Front Guide (6D) and align the Front Guide (6D), Rear Guide (6F) and Diamond Blade (2E) with the line on the surface. [. . . ] If changing from a small to a very large DIAMOND BLADE (2E) on a machine with a single speed gearbox, the Blade Shaft Pulleys (3-1L), Gearbox Pulleys (3-1N), the BLADE SHAFT FLANGES (2B & 2F), and the Blade Guard must be changed. For example, to change a single speed gearbox model from a 18" (450mm) drive to a 36" (900mm) drive: 1. E) Verify that machine drive configuration and blade shaft speed corresponds with 20-36 drive configuration information in operation manual. f) Install the 20-36 drive configuration decals (Decal 522627702 is required). [. . . ]