User manual HUSQVARNA FS 400 LV

[. . . ] The user advice and spare parts mentioned in this document are given as an indication, and do not constitute an undertaking. No warrantee will be granted in the event of errors or omissions, or for damage occurring during delivery, or caused by the design or use of the machine. We are very concerned about the quality of our products and we reserve the right to make any technical modifications to improve them, without warning. Prevent accidents due to unsuitable use, by an untrained person, during maintenance, repairs, overhauls, handling or transport · improve the reliability and durability of the machine · Ensure correct use, regular maintenance, and fast fault finding in order to reduce repair costs and downtime. [. . . ] Use : wet sawing new and old concrete and asphal Tools : Diamond Blades - water cooled Ø 350 mm or 400 mm or 450 mm - bore 25. Carefully read and understand all instructions before operating the saw. Aways wear safety approved hearing, eye, head and respiratory protection. Keep all parts of your body away from the blade and all other moving parts. inspect the blade , flanges and shafts for damage before installing the blade. Use only blades marked with a maximum operating speed greater than the blade shaft speed. Use caution and follow the instructions when loading and unloading the saw. 04 - Water intake tap 05 - Service spanner 06 - Engine Moteur 07 - Disk casing Carter de disque 08 - Front guide Guide avant 09 - Lifting ring Anneau d'élingage 10 - Belt cover Carter de courroies 11 - Engine oil Sortie de vidange moteur 12 - Motor tensioning screw 13 - Tank 14 - Motor stop 15 - Circuit breaker 16 - Connector 17 - RCCB 18 - RCCB connector 19 - Wheel Lock The operator must wear protective clothing appropriate to the work he is doing. Use only blades marked with a maximum operating speed greater than blade shaft speed Petrol engine machine maintenance manual) : (consult the engine Take into account the working conditions from health and safety point of wiew. As the engine often operates at an angle, check the oil level (with the engine horizontal) frequently to ensure that it never falls below the second mark on the dipstick. For transporting by vehicle or by any kind of lifting gear, there is a factory-fitted hoisting point on the machine. ELECTRICAL SAFETY : Operate this machine only on a supply equipped with a 30 mA earthed current-limiting circuitbreaker. Please read the instructions for use prior to operating the machine for the first time. The working area must be completely cleared, well lit and all safety hazards removed (no water or dangerous The RCCB must be used correctly, including testing it regularly. For tools supplied with an integral RCCB in the cable or in the mains plug, if the cable or plug has been damaged, repairs must be carried out by the manufacturer, one of his agents or by a qualified repair workshop to avoid any risks resulting from errors. Motor power supply: reinforced electric cable with 4 (3P+E) or 5 (3P+N+E) conductors 2. Direction of rotation of the motor : Direction of rotation on the right hand side of the cover (if the motor does not turn in the direction required Always keep blade guard in place. Fold down the front guide and position the machine so that the guide (F) and the blade line up with the mark. Take care about the direction of rotation which is shown by an arrow on one of the faces (direction of rotation on the right side of the guard) Make sure the contact faces of flanges (B and C) of blade and the axle are clean. Firmly lock screw (D) using the spanner supplied with the machine whilst immobilising the blade by hand. Replace all protective covers for your safety and that of other persons. Start moving down to the depth of cut required, indicated on the gradiated scale fitted on the side. [. . . ] The manufacturer declines all responsibility for loss or damage resulting from misuse or any modification, alteration or powering that does not conform to the manufacturer's original specifications. When working in a limited or closed area, make sure that the ventilation is adequate. The exhaust gases contain carbon monoxide (exposure to this toxic gas can cause loss of consciousness and can be fatal). We carry out all repairs in the shortest possible time and at the most economical prices (see overleaf for our address). [. . . ]