User manual HUSQVARNA CG46A

[. . . ] Do ct to da bje d or su cke cra G wer riorat a rec ly NINte mod detiee on era an Us t WARop wear ged. om un G wer riorat a rec ly NINte mod detiee on era an Us t WARop wear ged. no Do ct to dama or bje d su cke cra Do ct to da bje d or su cke cra G wer riorat a rec ly NINte mod detiee on era an Us t WARop wear ged. CG46A 46 Inch Mower Grass Catcher · · · · · Assembly Operation Customer Responsibilities Service and Adjustments Repair Parts 1 532151673 06. 28. 99 REV. [. . . ] no Do ect to dam or subj ked crac DUMP BAG INDICATOR r is ne ntai en d. Coe wh r. Re cont erlyi ently ent prop qu em r is g frereplac aine k ba d cont Checmende m less n. un ratio reco er a INGmow tierio ly on RNerate and de e Us WA t op wear aged. no Do ect to dam or subj ked crac CHUTE LATCH r is ne ntai en d. Coe wh r. Re cont erlyi ently ent prop qu em r is g frereplac aine k ba d cont Checmende m less n. un ratio reco er a ING ow tierio ly m on RNerate and de e Us WA t op wear aged. no Do ect to dam or subj ked crac LOWER CHUTE GRASS CATCHER CONTAINERS LOWER CHUTE ATTACHING STRAPS NOTE: When right hand (R. H. ) and left hand (L. H. ) are mentioned in this manual, it means when you are seated on the tractor, in the operator's position. THESE ARE THE TOOLS YOU WILL NEED TO ASSEMBLE YOUR GRASS CATCHER: (1) 1/2" Wrench (1) 1/2" Socket (1) 5/8" Socket (1) Drive Ratchet (1) 3" or longer Extension (1) Short Handle Phillips Screwdriver CAUTION: BEFORE ASSEMBLING GRASS CATCHER TO TRACTOR: · · · · · · Depress clutch/brake pedal fully and set parking brake. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 6 ASSEMBLY 1 · · REAR MOUNTING BRACKET and SUPPORT PLATE (See Figs. 1 & 2) Use Hardware - - GROUP "A" 2 · · COVER SEAL (See Fig. 3) No hardware required Install support plate to inside of drawbar as shown, using two (2) 7/16-14 x 3/4 hex bolts and the two threaded upper holes in the plate. Do not tighten at this time. Align mark on seal with mark at cover opening. Work seal into opening so cover sits between flanges of seal. NOTE: Be sure to align the four (4) lower threaded holes of the support plate with the holes in the drawbar. Assemble the mounting bracket as shown to the outside of the drawbar using four (4) 7/16-14 x 3/4 hex bolts and the four (4) lower threaded holes of the support plate. Tighten all hardware securely. ALIGNMENT MARKS HEX BOLTS THREADED UPPER HOLES Fig. 3 SUPPORT PLATE COVER SEAL 3 · · SUPPORT POST (See Fig. 4) Use Hardware - - GROUP "B" DRAWBAR CAUTION: Container support is spring loaded and locked to the cover. Handle cover assembly carefully so as not to unlatch the cover from the container support. 6 8 ASSEMBLY 6 · · CONTAINER MOUNTING (See Fig. 7) No hardware required 7 · · · · LOWER CHUTE (See Fig. 8 & 9) Use Hardware - - GROUP "D" Install one container to left side first with warning to outside of unit. Install another container to center position and one in right position. NOTE: Right container should always overlap left container at center supports. [. . . ] Reinstall containers making sure right container overlaps left container at center supports. Close cover and secure latches over center support tubes. · · CAUTION · · Do not operate mower with grass catcher partially installed. Disengage blades and stop engine before leaving tractor seat to empty containers, unclogging chutes, etc. Disengage mower when crossing driveways or gravel surfaces and other areas where thrown objects could be a hazard. [. . . ]