User manual HUSQVARNA CG200 S

[. . . ] The user advice and spare parts mentioned in this document are given as an indication, and do not constitute an undertaking. No warrantee will be granted in the event of errors or omissions, or for damage occurring during delivery, or caused by the design or use of the machine. We are very concerned about the quality of our products and we reserve the right to make any technical modifications to improve them, without warning. Prevent accidents due to unsuitable use, by an untrained person, during maintenance, repairs, overhauls, handling or transport · improve the reliability and durability of the machine · Ensure correct use, regular maintenance, and fast fault finding in order to reduce repair costs and downtime. [. . . ] tOOLS - Applications : · Star Cutting Head : - Cleaning/removal of epoxy paint, oil and glazes, glue, thermo plastic road marking. That the warnings and instructions marked on the machine are followed (adequate personal protection, correct use, general safety instructions, etc). That no modification, transformation or addition is detrimental to safety and that it is carried out without prior authorization from the manufacturer. Always keep it perfectly clean · Always keep alert when working · Check that the parts are properly fixed (no abnormal vibration) and that it is correctly assembled. 1 - Safety lever (dead man's handle) 2 - Steering shaft 3 - Depth adjustment knob (mm) 4 - Spanner 5 - Shaft adjustment knob 6 - Quick raise/lower lever 7 - Sling loop 8 - Engine / Motor 9 - On / off switch 10 - Belt guard 11 - Chassis Fit the drum (H) and slid it on its shaft (J). To mill up to a wall, fit the side drum (K), housing (L), plate (M) and bearing (N) in the place of the original drum and plate [SEE FIG. 13 - Drain extension 14 - Quick release guard 15 - Centring dome nuts 16 - Dust extractor hose 17 - Transmission 18 - 200 mm wide drum 19 - Floor edge drum (optional) 20 - Supply cable Please read the instructions for use prior to operating the machine for the first time. The working area must be completely cleared, well lit and all safety hazards removed (no water or dangerous objects in the vicinity) Upon installation at the work site, the machine can be moved without running the engine simply by pushing it along on its three wheels. The operator must wear protective clothing appropriate to the work he is doing. We recommend that this includes both eye and ear protection Any persons not involved in the work should leave the working area Get into a comfortable, balanced position. Remove all adjustment tools and wrenches from floor and machine To start the planer, grasp the dead man's handle (I) on the steering shaft. Take into account the working conditions from health and safety point of wiew. - To start the engine, refer to the engine operating instructions and paragraph 7 "Starting up". DUST EXTRACTOR: - Fit the suction (U) hose directly onto connector located on the back of the machine (health and safety) [SEE FIG. ELECTRICAL SAFETY : Operate this machine only on a supply equipped with a 30 mA earthed currentlimiting circuit-breaker. - THREE PHASE : Check that the motor is turning in the same direction as that of the arrow located on rear cover of the motor (if not, reverse 2 of the wires). To mill concrete, pass the machine over several times according to the nature of concrete and until desired result is obtained. Quick release: - Pull lever (B) backwards to release the drum quickly. Check periodically belt tension and retighten it when necessary but do not overtighten, by means of the nut (S) and lock nut (T) [SEE Never set belts beyond original tension After some hours of use, carry out a general retightening of all nuts and bolt. - Have tested by an electrician or contact the service department - Contact the service department to have the motor replaced - Engine stopped. [. . . ] Vi finns alltid till hands för dig för att reparera din maskin inom kortast möjliga tid och till våra bästa priser (adressen finns på baksidan). WARRANTY The warranty is limited to the free of charge replacement of parts recognised as defective by Husqvarna (excluding wear components and consumables) providing the repair is made within after-sales service of Husqvarna or a recognised Husqvarna repair centre. The manufacturer is not responsible for any direct or indirect, material or immaterial, damages caused to persons or things by failure of the machine or the non operation of the machine. WARRANTY CONDITIONS To benefit the warranty, it is necessary to return the joined warranty certificate, duly completed, to Husqvarna within eight days of the purchase. [. . . ]