User manual HUSQVARNA C36C

[. . . ] Do ct to da or subjeed ck cra r un ra a re INGmowe tierio ly on RNerate and de e Us WA t op wear ged. Re conta erlyiently nt prop qu ceme r is g frerepla ine ba nta eck ded en s co Ch les tion. comm Do ct to da or subjeed ck cra r un ra a re INGmowe tierio ly on RNerate and de e Us WA t op wear ged. Re conta erlyiently nt prop qu ceme r is g frerepla ine ba nta eck ded en s co Ch les tion. [. . . ] omme r un rat rec we tierio ly a mo on RNerate and de e Us WA t op wear ged. no Do ct to dama or subjeed ck cra ING CHUTE LATCH r is taine . Con en led ce wh r. Handle cover assembly carefully so as not to unlatch the cover from the container support. Rotate cover assembly onto its side as shown. Assemble support post to container support with the three (3) carriage bolts and locknuts. Tighten securely. SHOULDER BOLTS LANCED TABS TOWARD BOTTOM FIG. 2A If your tractor does not have four (4) shoulder bolts installed on the drawbar, follow the instructions below. CARRIAGE BOLTS Use Hardware - - GROUP "B" · · Using the four formed holes in the drawbar, install the four shoulder bolts as shown and tighten securely. Hang the mounting bracket, lanced tabs towards bottom, on the bolts. SUPPORT POST SELF TAPPING SHOULDER BOLTS LOCKNUTS FIG. 5) Use Hardware - - GROUP "D" NOTE: For ease of assembly, you may wish to obtain the assistance of another person for mounting assembly to tractor. · With cover closed, lift assembly and place support post inside mounting bracket. · Line up holes in mounting bracket with holes in support post and insert bracket support pin. · Install the three (3) tubing end caps onto container support. · Tap each end cap onto container support tubes to seat securely. BRACKET SUPPORT PIN COVER ASSEMBLY 6 · · · · CONTAINER ASSEMBLY (See Fig. 6) No hardware required Place bottom half inside of top half, as shown. Place one foot inside bottom half and lift top half to meet bottom half. Press halves tightly together while lifting top to lock into place as shown. IMPORTANT: BEFORE LOCKING THE TABS, HOOKED EDGES ON BOTH HALVES MUST OVERLAP TO FORM SEAL AS SHOWN IN INSET. Repeat for second container. CONTAINER BOTTOM HALF CONTAINER TOP HALF CONTAINER BOTTOM HALF RETAINER SPRING PRESS TOGETHER TO FORM SEAL WHILE LIFTING TOP HALF LOCKING TAB ASSEMBLY CHECK: Squeeze sides of lower half of container and check that there is no gap between upper and lower halves. If a gap appears, unlock tabs to separate container halves and repeat instructions above. END CAP SUPPORT POST r is ne tai en . Con wh r. Re conta erlyientlyment prop qu ce r is g fre pla ine ba d re nta eck de s co Ch en les tion. comm r unriora a re INGmowe tie only de RNerate and Use WA t op wear ged. 7) No hardware required WASHER WASHER LOCK WASHER LOCK WASHER LATCH LATCH WELD NUT WELD NUT SCREW Install one container to left side first with warning to outside of unit. NOTE: Right container should always overlap left container at center support. · Close cover and lock latch handle over center support tube. FIG. 8A COVER LATCH HANDLE CONTAINER WARNING AD INR n o s to GtNepo tcejbuc r r e a ot ca o m ew dek re w a ra d ro lnu dn a se ed a m c s eit e g n o t a r oi r s U . [. . . ] · Place gearshift/motion control lever in neutral (N) position. · Make sure blades and all moving parts have completely stopped. · Disconnect spark plug wire(s) from spark plug(s) and place wire where it cannot come in contact with plug. CAUTION: Do not leave grass in bagger containers. Failure to do so may result in spontaneous combustion which could develop into a fire. TO REMOVE GRASS CATCHER Reverse appropriate steps in ASSEMBLY section of this manual. CAUTION: Grass catcher components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. [. . . ]