User manual HUSQVARNA 965896501

[. . . ] Printed in U. S. A. Contents INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Towing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Operating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Good Service. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] (See “Battery” in the Maintenance Section. ) If “jumper cables” are used for emergency starting, follow this procedure: Jumper Cables • Connect each end of the RED cable to the POSITIVE (+) terminal on each battery, taking care not to short against chassis. • Connect one end of the BLACK cable to the NEGATIVE (-) terminal of the fully charged battery. • Connect the other end of the BLACK cable to a good CHASSIS GROUND on the mower with the discharged battery, away from the fuel tank and battery. To remove cables, reverse order • Remove BLACK cable first from chassis and then from the fully charged battery. • Remove RED cable last from both batteries. Jumper cable connection 8011-642 28-Husqvarna operation Running 1. Release the parking brake by pushing the button and moving the lever downward. When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake will shut off the engine. 2. Move the steering controls to the neutral position (N). Parking brake released 8058-020 3. Set retaining pin into selected cutting height and secure the opposite side with a cotter hairpin. WARNING!Make sure the work area is free from objects that could be thrown by the rotating blades. Secure selected cutting height 8058-024 4. Push the release button on the cutting height lever and move lever to the pin, release the button. 5. Set the cutting height with the cutting height adjustment lever. Mower deck lifting lever 8058-019 Husqvarna-29 operation 6. Engage the mower deck by pulling out the blade switch. The machine’s speed and direction are continuously variable using the two steering controls. When both controls are in the neutral position, the machine stands still. Avoid sudden directional changes. Husqvarna-31 operation Stopping the Engine Allow the engine to idle a minute in order to attain normal operating temperature before stopping it, if it has been worked hard. Avoid idling the engine for longer periods, as there is a risk of the spark plugs fouling. • Disengage the mower deck by depressing the blade switch. ST FA CHOKE UP BLADES ON DOWN BLADES OFF OW SL Disengage the mower deck and move throttle to minimum 8052-001 • • Raise the mower deck by pressing the button on the lever and pullng backward to the transport position. When the machine is standing still, activate the parking brake by pushing the lever button and pulling the lever upward. Turn the ignition key to the stop position. • The mower deck’s lifting lever 8058-019 • • Move the steering controls outward. Always remove key when leaving the mower to prevent unauthorized use. IMPORTANT INFORMATION Leaving the ignition switch in any other position than “OFF” will cause the battery to be discharged. Place controls in neutral position 32-Husqvarna 8061-026 operation Manual Transport ZT-2800 Bypass Linkages When pushing or pulling the mower, engage the ZT-2800 (Integrated Zeroturn Transaxle) bypass linkages. The ZT-2800 bypass linkages are located on the rear of the frame, below the rear engine guard. Release the levers with the head outside the frame and held in the bypass position. Load the machine into truck or trailer by driving up ramps in low gear. The machine is not intended to be lifted by hand. Bypass linkage, ZT-2800 engaged 8058-032 WARNING!Make no adjustments without: • • • the engine stopped, the ignition key removed, the parking brake activated Pump Release Valves Pump release valves are located at the left and right of the pump. [. . . ] SECTION 3 - ITEMS NOT COVERED BY THIS WARRANTY The following items are not covered by this warranty: (1) Normal customer maintenance items which become worn through normal regular use, including, but not limited to belts, blades, blade adapters, bulbs, clutches, clutch drums, filters (fuel line, fuel filters, air filters, oil filters), sprockets, guide bars, lubricants, rewind springs, spark plugs; (2) Natural discoloration of material due to ultraviolet light; (3) Engine and drive systems not manufactured by Husqvarna; these items are covered by the respective manufacturer’s warranty as provided in writing with the product information supplied at the time of purchase; all claims must be sent to the appropriate manufacturer. (4) Lawn and garden attachments that are covered by a third party which gives a warranty, all claims for warranty should be sent to the manufacturer. (6) Emission Control System components necessary to comply with CARB-TIER II and EPA regulations which are manufactured by third party engine manufacturer. SECTION 4 - EXCEPTIONS AND LIMITATIONS This warranty shall be inapplicable to defects resulting from the following: (1) Accident, abuse, misuse, negligence and neglect, including stale fuel, dirt, abrasives, moisture, rust, corrosion, or any adverse reaction due to incorrect storage or use habits; (2) Failure to operate or maintain the unit in accordance with the Owner’s/Operator’s manual or instruction sheet furnished by Husqvarna; (3) Alterations or modifications that change the intended use of the product or affects the product’s performance, operation, safety, or durability, or causes the product to fail to comply with any applicable laws; or: (4) Additional damage to parts or components due to continued use occurring after any of the above. [. . . ]