User manual HUSQVARNA 96093001200

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA 96093001200. We hope that this HUSQVARNA 96093001200 user guide will be useful to you.


HUSQVARNA 96093001200 : Download the complete user guide (1450 Ko)

Manual abstract: user guide HUSQVARNA 96093001200

Detailed instructions for use are in the User's Guide.

[. . . ] DRT900H Owner's Manual / 96093001200 / 2009-12 532 43 08-18 SAFETY RULES Safe Operation Practices for Walk-Behind Powered Rotary Tillers • TRAINING • • • • • • • • • • Read the Manual carefully. Be thoroughly familiar with the controls and the proper use of the equipment. Never allow adults to operate the equipment without proper instruction. Keep the area of operation clear of all persons, particularly small children, and pets. PREPARATION • • • • • • • • • • Thoroughly inspect the area where the equipment is to be used and remove all foreign objects. [. . . ] Hard soil should be moistened before tilling; however, extremely wet soil will “ball-up” or clump during tilling. When tilling in the fall, remove vines and long grass to prevent them from wrapping around the tine shaft and slowing your tilling operation. TO START ENGINE (See Fig. 14) CAUTION: Keep tine control in “OFF” position when starting engine. When starting engine for the first time or if engine has run out of fuel, it will take extra pulls of the recoil starter to move fuel from the tank to the engine. • Move shift lever indicator to “N” (neutral) position. • Grasp recoil starter handle with one hand and grasp tiller handle with other hand. Pull rope out slowly until engine reaches start of compression cycle (rope will pull slightly harder at this point). Do not let starter handle snap back against starter. • • 10 OPERATION • Do not lean on handle. To get through a really tough section of sod or hard ground, apply upward pressure on handle or lower the depth stake. ADJUST WHEELS FOR CULTIVATING (See Figs. 17 and 18) • Place blocks under right hand side of tiller and remove hairpin clip and clevis pin from right hand wheel. • Move wheel outward approximately 1 inch until hole in inner wheel hub lines up with inner hole in axle. • Replace clevis pin and hairpin clip on inside of wheel and remove blocks. NOTE: In extremely rough conditions and while cultivating, the wheels should be moved outward on the axle for increased stability. OUTER VIEW OF TIRE CLEVIS PIN 4 5 3 6 2 7 1 Fig. 15 CULTIVATING Cultivating is destroying the weeds between rows to prevent them from robbing nourishment and moisture from the plants. At the same time, breaking up the upper layer of soil crust will help retain moisture in the soil. Lower the outer side shields to protect small plants from being buried. • Cultivate up and down the rows at a speed which will allow tines to uproot weeds and leave the ground in rough condition, promoting no further growth of weeds and grass (See Fig. • Do not lean on handle, this takes weight off the wheels, reduces traction, and may cause the tiller to skip over the ground. • Always lower the drag stake when using the forward rotating tine drive. HAIRPIN CLIP tire_1 Fig. 17 INNER VIEW OF TIRE CLEVIS PIN HAIRPIN CLIP tire_2 Fig. 16 11 MAINTENANCE US RS RS OU 0H Y5 ER YS EA S MAINTENANCE SCHEDULE EA RE E UR OU CH HO FILL IN DATES AS YOU COMPLETE REGULAR SERVICE Check Engine Oil Level Change Engine Oil Oil Pivot Points Inspect Spark Arrester / Muffler Inspect Air Screen Clean or Replace Air Cleaner Cartridge Clean Engine Cylinder Fins Replace Spark Plug RH Gear Case Grease Fitting (1oz. ) Y5 ER Y2 FO ER ER 5H SO N EV BE EV 1, 2 2 1 - Change more often when operating under a heavy load or in high ambient temperatures. 2 - Service more often when operating in dirty or dusty conditions. EV EV SERVICE DATES GENERAL RECOMMENDATIONS The warranty on this tiller does not cover items that have been subjected to operator abuse or negligence. [. . . ] 532 13 28-01 532 10 46-79 812 00 00-32 532 15 92-29 532 10 23-84 532 10 21-41 874 76 06-16 532 10 23-83 532 10 23-31 532 13 08-12 874 76 05-44 532 14 00-62 532 17 04-88 873 80 05-00 873 97 05-00 819 13 13-12 874 76 05-24 873 51 06-00 532 16 41-73 DESCRIPTION Belt, V Pulley, Idler Ring, Klip Bracket, Idler Bolt, Hex 5/16-16 x 12 Shaft, Idler Arm Bolt, Hex 3/8-16 x 1 Counterweight, L. Sheave, Engine Bolt, Fin Hex 5/16-18 unc x 2-3/4 Cap, Plunger Blk Screw Hex Wsh Slt #10-24 x 1/2 Nut Lock Hex w/Ins 5/16-18 unc PL Nut Lock Hex Flange Washer 13/32 x 13/16 x 12 Ga. Bolt, Hex 5/16-18 x 1-1/2 Nut Keps Hex 3/8-16 unc Keeper Belt Engine NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm 21 REPAIR PARTS TILLER - - MODEL NUMBER DRT900H (96093001200), PRODUCT NUMBER 960 93 00-12 MAINFRAME, RIGHT SIDE KEY NO. PART NO. DESCRIPTION KEY NO. PART NO. DESCRIPTION 2 5 7 10 11 12 13 873 97 05-00 532 10 23-32 532 10 21-73 874 76 05-24 532 12 47-88 532 12 68-75 532 10 21-90 532 15 07-40 532 12 47-18 Locknut, Hex, Flange 5/16-18 Bracket, Reinforcement Counter Weight, R. H. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 96093001200




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 96093001200 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.