User manual HUSQVARNA 96043003900

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA 96043003900. We hope that this HUSQVARNA 96043003900 user guide will be useful to you.


HUSQVARNA 96043003900 : Download the complete user guide (4751 Ko)

Manual abstract: user guide HUSQVARNA 96043003900

Detailed instructions for use are in the User's Guide.

[. . . ] 03002 YTH20F42T Owner's Manual / 96043003900 / 2007-12 SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. WARNING: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. [. . . ] Using a blade not approved by the manufacturer of your tractor is hazardous, could damage your tractor and void your warranty. BRAKE OPERATION If tractor requires more than five (5) feet to stop at highest speed in highest gear on a level, dry concrete or paved surface, then brake must be serviced. (See “TO CHECK BRAKE” in the Service and Adjustments section of this manual). TIRES • Maintain proper air pressure in all tires (See PSI on tires). • Keep tires free of gasoline, oil, or insect control chemicals which can harm rubber. • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position. CHECK OPERATOR PRESENCE SYSTEM • When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. • When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. • The attachment clutch should never operate unless the operator is in the seat. ROS "ON" Position Engine "ON" Position (Normal Operating) BLADE REMOVAL (See Fig. 13) • Raise mower to highest position to allow access to blades. NOTE: Protect your hands with gloves and/or wrap blade with heavy cloth. • Install new blade with stamped "GRASS SIDE" facing the ground. IMPORTANT: To ensure proper assembly, center hole in blade must align with star on mandrel assembly. IMPORTANT: Special blade bolt is heat treated. STAR CENTER HOLE 02 54 5 BLADE BLADE BOLT (SPECIAL) MANDREL ASSEMBLY FIG. 13 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. NOTE: The original equipment battery on your tractor is maintenance free. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Clean terminals and battery cable ends with wire brush until bright. 02828 CHECK REVERSE OPERATION (ROS) SYSTEM • When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine. [. . . ] 532 40 66-21 532 18 01-66 532 14 06-75 873 80 06-00 532 12 41-81 532 17 18-77 532 19 69-77 532 17 18-52 DESCRIPTION Seat Bracket Pivot Fender Strap, Asm Fender Nut, Lock W/Ins. 3/8-16 unc Spring, Seat Cprsn Bolt 5/16-18 uncx 3/4 w/Sems Pan, Seat Bolt, Shoulder 5/16-18 KEY NO. 873 80 05-00 532 19 76-61 532 19 82-00 874 76 06-12 819 13 38-12 DESCRIPTION Nut, Lock 5/16-18 unc Handle Slide Seat Spring Latch Seat Bolt Fin Hex 3/8-16 unc x 3/4 Washer 13/32 x 2-3/8 x 12 Ga. NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 36 TRACTOR - - MODEL NUMBER YTH20F42T (96043003900), PRODUCT NO. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 96043003900




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 96043003900 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.