User manual HUSQVARNA 96043000802

[. . . ] 03002 YTH2448T Owner's Manual SAFETY RULES Safe Operation Practices for Ride-On Mowers DANGER: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. • WARNING: In order to prevent accidental starting when setting up, transporting, adjusting or making repairs, always disconnect spark plug wire and place wire where it cannot contact spark plug. WARNING: Do not coast down a hill in neutral, you may lose control of the tractor. WARNING: Tow only the attachments that are recommended by and comply with specifications of the manufacturer of your tractor. [. . . ] • Avoid stumps, stones, deep ruts, sharp objects and other hazards that may cause tire damage. NOTE: To seal tire punctures and prevent flat tires due to slow leaks, tire sealant may be purchased from your local parts dealer. OPERATOR PRESENCE SYSTEM AND REVERSE OPERATION SYSTEM (ROS) Be sure operator presence and reverse operation systems are working properly. If your tractor does not function as described, repair the problem immediately. • The engine should not start unless the brake pedal is fully depressed, and the attachment clutch control is in the disengaged position. CHECK OPERATOR PRESENCE SYSTEM • When the engine is running, any attempt by the operator to leave the seat without first setting the parking brake should shut off the engine. • When the engine is running and the attachment clutch is engaged, any attempt by the operator to leave the seat should shut off the engine. • The attachment clutch should never operate unless the operator is in the seat. ROS "ON" Position Engine "ON" Position (Normal Operating) MANDREL ASSEMBLY FIG. 13 BATTERY Your tractor has a battery charging system which is sufficient for normal use. However, periodic charging of the battery with an automotive charger will extend its life. NOTE: The original equipment battery on your tractor is maintenance free. TO CLEAN BATTERY AND TERMINALS Corrosion and dirt on the battery and terminals can cause the battery to “leak” power. • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Clean terminals and battery cable ends with wire brush until bright. • Reinstall battery (See “REPLACING BATTERY" in the SERVICE AND ADJUSTMENTS section of this manual). 02828 CHECK REVERSE OPERATION (ROS) SYSTEM • When the engine is running with the ignition switch in the engine "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should shut off the engine. • When the engine is running with the ignition switch in the ROS "ON" position and the attachment clutch engaged, any attempt by the operator to shift into reverse should NOT shut off the engine. BLADE CARE For best results mower blades must be sharp. Replace worn, bent or damaged blades. 15 MAINTENANCE V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. TRANSAXLE COOLING The transmission fan and cooling fins should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. To prevent possible damage to seals, do not use high pressure water or steam to clean transaxle. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. [. . . ] w/Lower Bearing Housing, Mandrel Bearing, Ball, Mandrel Washer 3/8 Bolt RdHd 5/16-18 unc x 5/8 Pin Cotter 5/16 Bowtie Baffle Vortex Nut, Crownlock 5/16-18 unc Stripper Mandrel Cap Sleeve Spring, Torsion Nut, Push Defl ector Shield Rod, Hinge Screw, Thdroll Washer Head Washer, Spacer Mower Vented Pulley, Mandrel Nut, Flg. 46 47 48 49 50 52 54 97 98 113 114 116 117 120 122 185 187 188 189 190 194 --- PART NO. 532 13 77-29 532 19 72-42 532 19 61-06 873 90 06-00 872 11 06-12 532 17 79-68 817 49 06-36 532 17 85-15 532 19 61-05 872 11 05-08 532 19 74-51 532 19 34-06 532 17 48-73 819 13 20-12 532 18 75-57 873 90 07-00 532 19 51-61 873 90 05-00 532 19 51-85 532 19 65-39 872 14 07-16 532 18 72-92 DESCRIPTION Screw, Thdroll. 3/8-16 unc Bolt Carr SH 3/8-16 x 1-1/2 Gr. 5 Pulley Idler Clutching Screw 3/8-16 x 2-1/4 Washer Hardened Spring Drive Bolt Rdhd Sqnk 5/16-18 x 3/4 Rod Tension Relief Bolt, Shoulder Gauge Wheel Washer 13/32 x 1-1/4 x 12 Ga. [. . . ]