User manual HUSQVARNA 954830071B

[. . . ] LT130 Owner’s Manual SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. • • • • • • • • • • • • • • • GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, toys, wire, etc. , which could be picked up and thrown by the blade. [. . . ] • Disconnect BLACK battery cable first then RED battery cable and remove battery from tractor. • Clean terminals and battery cable ends with wire brush until bright. • Reinstall battery (See “CONNECT BATTERY” in the Assembly section of this manual). IMPORTANT: BLADE BOLT IS GRADE 8 HEAT TREATED. NOTE: We do not recommend sharpening blade - but if you do, be sure the blade is balanced. BLADE MANDREL ASSEMBLY TRAILING EDGE FLAT WASHER LOCK WASHER HEX BOLT (GRADE 8)* *A GRADE 8 HEAT TREATED BOLT CAN BE IDENTIFIED BY SIX LINES ON THE BOLT HEAD. FIG. 14 15 CUSTOMER RESPONSIBILITIES V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. Replace belts if they begin to slip from wear. OIL FILL CAP/DIPSTICK TRANSAXLE COOLING Keep transaxle free from build-up of dirt and chaff which can restrict cooling. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF or SG. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES SAE 30 5W-30 °F °C -30° -20° -20° 0° 30° -10° 32°40° 0° 10° 60° 20° 80° 30° 100° 40° OIL DRAIN PLUG FIG. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first. • Carefully remove cartridge to prevent debris from entering carburetor. • Reinstall cartridge, nut, precleaner, cover and secure with knob(s). IMPORTANT: PETROLEUM SOLVENTS, SUCH AS KEROSENE, ARE NOT TO BE USED TO CLEAN THE CARTRIDGE. DO NOT USE PRESSURIZED AIR TO CLEAN OR DRY CARTRIDGE. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE NOTE: Although multi-viscosity oils (5W30, 10W30 etc. ) improve starting in cold weather, these multi-viscosity oils will result in increased oil consumption when used above 32°F. Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after the first two hours of operation and every 25 hours thereafter or at least once a year if the tractor is not used for 25 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level. • After oil has drained completely, replace oil drain plug and tighten securely. For approximate capacity see “PRODUCT SPECIFICATIONS” on page 3 of this manual. Keep oil at “FULL” line on dipstick. 16 CUSTOMER RESPONSIBILITIES MUFFLER COVER KNOB CARTRIDGE NUT COVER Inspect and replace corroded muffler and spark arrester (if equipped) as it could create a fire hazard and/or damage. SPARK PLUGS PAPER CARTRIDGE FOAM PRE-CLEANER BASE Replace spark plugs at the beginning of each mowing season or after every 100 hours of operation, whichever occurs first. Spark plug type and gap setting are shown in “PRODUCT SPECIFICATIONS” on page 3 of this manual. IN-LINE FUEL FILTER (See Fig. If fuel filter becomes clogged, obstructing fuel flow to carburetor, replacement is required. • Place new fuel filter in position in fuel line with arrow pointing towards carburetor. • Be sure there are no fuel line leaks and clamps are properly positioned. [. . . ] 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 * ** 532105928 532110084 532134394 532120473 532142678 532142679 532120407 532106589 532120408 532105937 532002226 532134401 532002264 532120474 532110081 532105941 532110071 532120952 532110082 532123908 532142680 532120961 532007294 532108989 532120953 532120954 532134799 532138244 532108996 532120956 532106596 532120951 532120416 DESCRIPTION Sprocket, 9 Teeth (Reverse) Gear, Bevel, 42 Teeth * Assembly, Kit, Shim . 750 Shaft Shaft, Drive Gear, Spur, 12 Teeth (1 ) Gear, Spur, 15 Teeth (2 ) Gear, Spur, 20 Teeth (3 ) Gear, Spur, 25 Teeth (4 ) Gear, Spur, 28 Teeth (5 ) Gear, Spur, 31 Teeth (6 ) Washer, Plain . 632 x 1. 00 x . 060 Washer, Neoprene Washer, Plain . 758 x 1. 25 x . 031 Axle, L. H. Gear, Miter, 15 Teeth Ring, Retaining Gear, Spur, 32 Teeth Shaft, Cross Gear, Miter, 15 Teeth Axle, R. H. Housing, Lower Puck, Friction Disc, Brake Spacer Jaw, Brake Pin, Dowel Screw, Self-Tapping, Large 5/16-18 x 2. 25 Lever, Actuating Washer, Plain . 321 x 1. 00 x . 055 Bracket, Anti-Rotation Screw, Self-Tapping, Large 5/16-18 x 1. 44 Puck, Friction Grease st nd rd th th th Use in combinations to maintain proper clearances Order Key No. inches 1 inch = 25. 4 mm 45 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION SIGHTING GUIDE CUT OUT ON D THIS OTT IS A ED L 15° S INES LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. 46 15° MAX. Operate your Tractor up and down the face of slopes (not greater than 15°), never across the face. [. . . ]