User manual HUSQVARNA 954140010H

[. . . ] YTH180 Owner’s Manual SAFETY RULES Safe Operation Practices for Ride-On Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. I. • • • • • • • • • • • • • • • GENERAL OPERATION Read, understand, and follow all instructions in the manual and on the machine before starting. Only allow responsible adults, who are familiar with the instructions, to operate the machine. Clear the area of objects such as rocks, toys, wire, etc. , which could be picked up and thrown by the blade. [. . . ] STAR MANDREL ASSEMBLY V-BELTS Check V-belts for deterioration and wear after 100 hours of operation and replace if necessary. 16 17 CUSTOMER RESPONSIBILITIES TRANSAXLE COOLING The fan and cooling fins of transmission should be kept clean to assure proper cooling. Do not attempt to clean fan or transmission while engine is running or while the transmission is hot. • Inspect cooling fan to be sure fan blades are intact and clean. • Inspect cooling fins for dirt, grass clippings and other materials. To prevent damage to seals, do not use compressed air or high pressure sprayer to clean cooling fins. OIL DRAIN PLUG AIR SCREEN OIL FILL CAP/DIPSTICK TRANSAXLE PUMP FLUID The transaxle was sealed at the factory and fluid maintenance is not required for the life of the transaxle. Should the transaxle ever leak or require servicing, contact your nearest authorized service center/department. FIG. 18) Air screen must be kept free of dirt and chaff to prevent engine damage from overheating. Clean with a wire brush or compressed air to remove dirt and stubborn dried gum fibers. ENGINE LUBRICATION Only use high quality detergent oil rated with API service classification SF, SG, or SH. Select the oil’s SAE viscosity grade according to your expected operating temperature. SAE VISCOSITY GRADES 10W30 5W-30 -20° °F °C -30° 0° -20° -10° 30° 32° 40° 0° 10° 60° 20° 80° 30° 100° 40° AIR FILTER (See Fig. Clean the foam pre-cleaner after every 25 hours of operation or every season. Service paper cartridge every 100 hours of operation or every season, whichever occurs first. TO SERVICE CARTRIDGE • Replace a dirty, bent, or damaged cartridge. NOTE: Do not wash the paper cartridge or use pressurized air, as this will damage the cartridge. • Reinstall the pre-cleaner (cleaned and oiled) over the paper cartridge. • Reinstall air cleaner cover and secure by tightening knob. TEMPERATURE RANGE ANTICIPATED BEFORE NEXT OIL CHANGE Change the oil after every 50 hours of operation or at least once a year if the tractor is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of operation. Tighten oil fill cap/dipstick securely each time you check the oil level. • After oil has drained completely, replace oil drain plug and tighten securely. For approximate capacity see “PRODUCT SPECIFICATIONS” section of this manual. Tighten cap onto the tube securely when finished. CARTRIDGE FOAM PRE-CLEANER CARTRIDGE PLATE KNOB RUBBER SEAL NUT 18 FIG. 19 CUSTOMER RESPONSIBILITIES CLEAN AIR INTAKE/COOLING AREAS To insure proper cooling, make sure the grass screen, cooling fins, and other external surfaces of the engine are kept clean at all times. [. . . ] 1 2 3 4 5 6 7 8 11 12 13 15 16 17 18 19 20 23 24 25 26 27 28 29 30 31 32 36 37 38 40 41 49 50 PART NO. 532159460 532159471 532105767 812000002 819211621 532120183 532125631 532124526 532139865 532139866 532124670 532127218 873350800 532130171 873680800 532139868 532163552 532110807 819131016 532124874 876020308 532126971 873350600 532138057 532150233 532140302 873540600 532155097 532123935 817490512 819112410 532155098 532145212 532110452 DESCRIPTION Wire Asm Inner/Spring W/Plunger LT Shaft Asm Lift RH w/Inf Pin Groove 1 500 Zinc E Ring #5133-62 Washer 21/32 X 1 X 21 Ga Bearing Nylon Blk 629 Id Grip Handle Fluted Blk Button Plunger Black Link Lift LH Fixed Length Link Lift RH Fixed Length Retainer Spring Link Front Nut Jam Hex 1/2-13 Unc Trunnion Blk Zinc Nut Crownlock 1/2-13unc Arm Suspension Rear Retainer Spring Nut Special Washer 13/32 X 5/8 X 16 Ga Spring 2-1/8" Pin Cotter 3/32 X 1/2 Rod Adj Lift Zinc 7. 49 Wrk Lg Nut Hex Jam 3/8-16 Unc Knob Inf 3/8-16 Unc Blk W/sym Trunnion Infin Height Bearing Pvt Lift Spherical Nut Crownlock 3/8 - 24 Indicator Height STLT Plug Hole Blk 1. 485/1. 515 Dia. Nut Hex Flange Lock Nut, Push Phos & Oil NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 45 SUGGESTED GUIDE FOR SIGHTING SLOPES FOR SAFE OPERATION SIGHTING GUIDE CUT OUT ON D THIS OTT IS A ED L 15° S INES LOP E ONLY RIDE UP AND DOWN HILL, NOT ACROSS HILL 46 SIGHT AND HOLD THIS LEVEL WITH SKY LINE OR TREE. 15° MAX. Operate your Tractor up and down the face of slopes (not greater than 15°), never across the face. [. . . ]