User manual HUSQVARNA 70 LP BROADCAST SPREADER

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA 70 LP BROADCAST SPREADER. We hope that this HUSQVARNA 70 LP BROADCAST SPREADER user guide will be useful to you.


HUSQVARNA 70 LP BROADCAST SPREADER : Download the complete user guide (2390 Ko)

Manual abstract: user guide HUSQVARNA 70 LP BROADCAST SPREADER

Detailed instructions for use are in the User's Guide.

[. . . ] For ease of assembly, make sure ON/OFF cable is on top of handle braces. With DOT on the handle assembly facing as shown, secure clamp bracket using a #10 x 3/4 slotted sheet metal screw. Install end of handle assembly between handle braces and secure with (2) 1/4-20 x 1 1/2” hex bolts and nuts. ON/OFF Cable Handle Assembly 1/4-20 Hex Nut 1/4-20 x 1 1/2” Hex Bolt 2 Handle Grip 4. Attach ON/OFF control to the upper handle using (2) #10 x 3/4” slotted sheet metal screws. [. . . ] Tipping the spreader too far can cause uneven spreading. SPREAD SWATH APPROX. The settings and swath widths on the product label are recommended starting points. Always check the delivery rate and pattern on a small area before treating a large area. Actual delivery rate can vary due to weather conditions, operating variables, and condition of the product being applied. See “HOW TO DETERMINE SPREADER SETTING AND SWATH WIDTH” for details. 7. (18 feet in 5 seconds) for full 8’ to 14’ spread pattern when applying fertilizer products. Apply header strips at each end of area to be treated then space trips across the area as shown. 4 8. Return leftover material to its original container. HOW TO DETERMINE SPREADER SETTINGS AND SPREAD WIDTH Two major factors should be considered when determining correct spreader settings of any product: 1. The product application rate, or the amount of material applied per 1, 000 square feet. The effective pattern width, or the actual width in which material is applied. Label settings are a guide and can be affected by numerous factors. EFFECTIVE PATTERN WIDTH A simple visual pattern test can be made by operating the spreader over a non-turf area and evaluating the pattern. A more accurate method is to place a row of common, disposable, aluminum cake pans approximately 1 foot on centers. Set the rate cam at a middle setting and make 3 or 4 passes in the same direction as shown. Pour the material collected from each pan into individual bottles of the same size. The effective pattern width is the distance out from the spreader to a point where the amount of material is 1/2 the average amount in the center pans. This distance is multiplied by 2 to achieve the total effective pattern width. APPLICATION RATE Knowing the effective pattern width (for example, 10 feet), measure a distance equal to 100 square feet (10’ x 10’ area covered). by taking the weight of the product and dividing it by the recommended square foot coverage (add two zeroes to the weight of the bag). Weigh remaining material left in hopper and adjust rate setting as required. [. . . ] Slide axle collar against the gear support and tighten axle collar set screw. Impeller surface should be cleaned periodically to remove build-up of product. Tire pressure should be 20-25 PSI. Oil Oil Oil Impeller Shaft Bearing In Hopper Oil Axle Collar NOTES 7 Parts List Model 70 LP 26 27 25 28 29 30 31 1 1A 2 32 24 23 3 4 7 5 6 22 21 20 19 16 15 8 18 17 PART OF OUR SERVICE IS PROVIDING REPLACEMENT PARTS. 28269 (800) 448-7543 14 10 7 13 12 11 9 Ke y 1 1A 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 Description Hopper Assembly Hopper * Shutoff Plate * Shutoff Plate Guides (Set)* Rate Cam & Chute Assembly * Impeller Assembly Frame Assembly Drive & Free Turning Wheel Axle Collar Axle Gear Gear Cover Assembly (2 Req. ) Gear Cover Clamp (3 Req. ) Axle Axle Bushing (2 Req. ) Impeller Pinion Gear Gear Support Part No. 525 56 82-06 525 56 82-07 525 56 84-03 525 56 84-04 525 56 83-03 525 56 87-05 525 556 92-02 525 56 96-02 525 56 86-06 525 56 86-05 525 56 88-05 525 56 88-06 525 56 86-07 525 56 86-08 525 56 87-01 525 56 88-07 525 56 88-08 Key No. 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 Description Impeller Shaft Screen Clip (2 Req. ) Hopper Screen Hopper Label * Handle Brace W/ Plug– LH. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 70 LP BROADCAST SPREADER




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 70 LP BROADCAST SPREADER will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.