User manual HUSQVARNA 65021 CHV

[. . . ] 65021CHV Owner’s Manual 532 41 10-43 12. 07. 06 BY Printed in U. S. A. Safe Operation Practices for Walk-Behind Mowers IMPORTANT: THIS CUTTING MACHINE IS CAPABLE OF AMPUTATING HANDS AND FEET AND THROWING OBJECTS. FAILURE TO OBSERVE THE FOLLOWING SAFETY INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH. CAUTION: Always disconnect spark plug wire and place wire where it cannot contact spark plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. WARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. [. . . ] SEE “CLEANING” IN MAINTENANCE SECTION OF THIS MANUAL. • • • TO STOP ENGINE • To stop engine, release operator presence control bar. In warmer weather over priming may cause flooding and engine will not start. If you do flood engine, wait a few minutes before attempting to start and do not repeat priming steps. The special mulching blade will recut the grass clippings many times and reduce them in size so that as they fall onto the lawn they will disperse into the grass and not be noticed. Also, the mulched grass will biodegrade quickly to provide nutrients for the lawn. Always mulch with your highest engine (blade) speed as this will provide the best recutting action of the blades. Wet grass tends to form clumps and interferes with the mulching action. At this time the grass has dried, yet the newly cut area will not be exposed to direct sunlight. For best results, adjust the lawn mower cutting height so that the lawn mower cuts off only the top one-third of the grass blades (See Fig. If the lawn is overgrown it will be necessary to raise the height of cut to reduce pushing effort and to keep from overloading the engine and leaving clumps of mulched grass. For extremely heavy mulching, reduce your width of cut by overlapping previously cut path and mow slowly. MAX 1/3 TO START ENGINE NOTE: Due to protective coatings on the engine, a small amount of smoke may be present during the initial use of the product and should be considered normal. To start a cold engine, push primer three (3) times before trying to start. This step is not usually necessary when starting an engine which has already run for a few minutes. Hold operator presence control bar down to the handle and pull starter handle quickly. 9 Certain types of grass and grass conditions may require that an area be mulched a second time to completely hide the clippings. When doing a second cut, mow across (perpendicular) to the first cut path. Mow north–south one week, then change to east–west the next week. This helps prevent matting/graining of lawn. • • MAINTENANCE BEFORE EACH USE Check for Loose Fasteners Clean / Inspect Grass Catcher * Check Tires Check Drive Wheels *** Clean Lawn Mower **** Clean under Drive Cover *** Check Drive Belt / Pulleys *** Check / Sharpen / Replace Blade Lubrication Clean and Recharge Battery ** Check Engine Oil level Change Engine Oil Clean Air Filter Inspect Muffler Replace Spark Plug Replace Air Filter Paper Cartridge Empty fuel system or add Stabilizer AFTER EACH USE EVERY 10 HOURS EVERY 25 HOURS OR SEASON EVERY 100 HOURS BEFORE STORAGE * (if so equipped) ** Electric-Start mowers *** Power-Propelled mowers **** Use a scraper deck to clean under 1 - Change more often if operating under a heavy load or in high outdoor temperatures. 5 - And after each 5 hours of use. GENERAL RECOMMENDATIONS The warranty on this lawn mower does not cover items that have been subjected to operator abuse or negligence. To receive full value from the warranty, operator must maintain mower as instructed in this manual. Some adjustments will need to be made periodically to properly maintain your unit. At least once a season, check to see if you should make any of the adjustments described in the Service and Adjustments section of this manual. • At least once a year, replace the spark plug, clean or replace air filter element and check blade for wear. [. . . ] 532 19 64-03 532 15 34-18 532 19 70-19 532 18 35-67 532 19 15-74 532 19 18-56 532 05 17-93 532 06 64-26 532 40 69-85 532 12 84-15 532 41 05-40 532 41 05-42 817 06 04-10 532 19 60-37 532 19 60-36 532 40 54-17 532 40 54-18 532 13 20-04 532 19 47-88 532 18 90-05 532 08 86-52 --- DESCRIPTION Upper Handle, with Foam Grip Lower Handle Control Bar Engine Zone Control Cable Handle Bolt Handle Knob Hairpin Cotter Wire Tie Rear Door Assembly Pop Rivet Support Bracket, LH Support Bracket, RH Screw 1/4-20 x 5/8 Handle Bracket Assembly, LH Handle Bracket Assembly, RH Spring, Rear Door, LH Spring, Rear Door, RH Keps Locknut 1/4-20 Rope Guide Rear Skirt Screw, Hinge 1/4-20 x 1/2 Engine, Briggs & Stratton, Model Number 124T02 (For engine service and replacement parts, call Briggs & Stratton at 1-800-233-3723) Hex Head Thread Rolling Screw 3/8-16 x 1-1/8 Hex Flange Nut Wheel & Tire Assembly, Rear, 12" Shoulder Bolt 5/16-18 x . 33 Axle Arm Assembly, Rear, RH Selector Knob Selector Spring KEY NO. 33 34 36 37 38 39 40 41 43 44 45 46 47 48 49 50 57 58 59 60 61 62 63 64 65 66 69 96 --- PART NO. 873 80 05-00 532 40 25-72 532 18 41-93 874 78 05-12 819 11 22-06 532 19 85-41 532 19 09-39 532 19 23-25 532 40 58-44 532 40 89-89 532 40 47-63 532 19 40-37 532 40 67-12 532 85 10-74 532 85 02-63 532 85 10-84 532 12 51-62 532 75 06-34 532 18 55-82 532 17 57-35 532 19 30-00 532 17 56-50 873 80 04-00 532 18 55-76 532 19 74-80 532 08 83-48 532 18 27-48 532 19 79-91 532 40 47-64 532 41 10-43 DESCRIPTION Nut, Hex 5/16-18 Axle Arm Assembly, Rear, LH Bolt Thread Cutting Screw w/Sems 5/16-18 x 3/4 Washer Nut, Hex Mounting Bracket, Debris Shield Screw Debris Shield Kit, Lawn Mower Housing (Includes Key Numbers 10, 11, 12 and 45) Danger Decal Blade Adapter / Pulley Blade, 21" Hardened Washer Helical Washer 3/8-24 x 1-3/8 Grade 8 Hex Head Machine Screw 3/8-24 x 1-3/8 Grade 8 Upstop Bracket Screw Discharge Deflector Hinge Bracket Spring Hinge Rod Nut, Hex Mulcher Door O-Ring Washer, Flat 1/2 Grip, Foam Clip, Cable Decal, Warning (not shown) Owner’s Manual, English / French 17 25 26 27 28 30 31 32 532 15 04-06 532 14 52-12 532 41 08-15 532 16 08-28 532 40 25-71 532 70 10-37 532 19 01-57 NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. [. . . ]