User manual HUSQVARNA 343 F

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA 343 F. We hope that this HUSQVARNA 343 F user guide will be useful to you.


HUSQVARNA 343 F : Download the complete user guide (2481 Ko)

You may also download the following manuals related to this product:

   HUSQVARNA 343 F (6153 ko)
   HUSQVARNA 343 F (6153 ko)
   HUSQVARNA 343 F (6153 ko)

Manual abstract: user guide HUSQVARNA 343 F

Detailed instructions for use are in the User's Guide.

[. . . ] Operator’s manual (EPA) 343F 345FX 345FXT 343FR 343FRM 343R 345RX Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING!Careless or incorrect use can result in serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of the operator’s manual. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. [. . . ] Ensure the machine is cleaned and that a complete service is carried out before long-term storage. The transport guard must always be fitted to the cutting attachment when the machine is being transported or in storage. • • This engine is certified to operate on unleaded gasoline. If you run the engine on a lower octane grade than 87 so-called knocking can occur. This gives rise to a high engine temperature and increased bearing load, which can result in serious engine damage. When working at continuous high revs a higher octane rating is recommended. • • ! Fuel WARNING!Bear in mind the risk of fire, explosion and inhaling fumes. • Two-stroke oil • For best results and performance use HUSQVARNA two-stroke engine oil, which is specially formulated for our air-cooled two stroke-engines. Never use two-stroke oil intended for water-cooled engines, sometimes referred to as outboard oil (rated TCW). Gasoline, litre 5 10 15 20 US gallon 1 2 1/2 5 Two-stroke oil, litre 2% (1:50) 0, 10 0, 20 0, 30 0, 40 US fl. The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. • • • ! WARNING!Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation. 22 – English FUEL HANDLING Mixing • • Always mix the gasoline and oil in a clean container intended for fuel. Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank. Fueling ! WARNING!Taking the following precautions, will lessen the risk of fire: Do not smoke or place hot objects near fuel. Always stop the engine and let it cool for a few minutes before refuelling. When refuelling, open the fuel cap slowly so that any excess pressure is released gently. Always move the machine away from the refuelling area before starting. • • • Do not mix more than one month’s supply of fuel at a time. If the machine is not used for some time the fuel tank should be emptied and cleaned. • • Clean the area around the fuel cap. Ensure that the fuel is well mixed by shaking the container before filling the tank. ! WARNING!Be aware of the fire hazard, especially when working near flammable substances and/ or vapours. English – 23 STARTING AND STOPPING Check before starting Starting and stopping • Check the blade to ensure that no cracks have formed at the bottom of the teeth or by the centre hole. The most common reason why cracks are formed is that sharp corners have been formed at the bottom of the teeth while sharpening or that the blade has been used with dull teeth. [. . . ] The table indicates the highest and lowest values. 38 – English TECHNICAL DATA 343R, 345RX Approved accessories Centre hole in blades/cutters, Ø 25, 4 mm Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Saw blade Plastic blades Maxi XS 200-22 (Ø 200 22 teeth) Scarlet 200-22 (Ø 200 22 teeth) Tricut Ø 300 mm Trimmy S Trimmer head Trimmy S II Auto 55 T45x Support cup Fixed With ball bearing 537 28 85-01 537 28 85-01 537 28 85-01 537 31 09-01 537 31 09-01 537 28 85-01 503 95 43-01 503 95 43-01 503 95 43-01 503 95 43-01 Cutting attachment guard, Art. no. 343F, 345FX, 345FXT Approved accessories Centre hole in blades/cutters, Ø 20 mm Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Maxi XS 200-22 (Ø 200 22 teeth) Saw blade Scarlet 200-22 (Ø 200 22 teeth) Scarlet 225-24 (Ø 225 24 teeth) Plastic blades Tricut Ø 300 mm Trimmy S Trimmer head Trimmy S II Auto 55 T45x Support cup Fixed With ball bearing 537 29 74-01 537 29 74-01 537 29 74-01 537 21 71-01 537 21 71-01 502 03 94-06 537 29 74-01 537 29 73-01 537 29 73-01 537 29 73-01 537 29 73-01 Cutting attachment guard, Art. no. English – 39 TECHNICAL DATA 343FR Approved accessories Centre hole in blades/cutters, Ø 25, 4 mm Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Saw blade Plastic blades Maxi XS 200-22 (Ø 200 22 teeth) Scarlet 200-22 (Ø 200 22 teeth) Tricut Ø 300 mm Trimmy S II Trimmer head Auto 55 T45x Support cup Fixed With ball bearing 537 28 85-01 537 28 85-01 537 28 85-01 537 31 09-01 537 31 09-01 537 28 85-01 503 95 43-01 503 95 43-01 503 95 43-01 Cutting attachment guard, Art. no. 343FRM Approved accessories Centre hole in blades/cutters, Ø 25, 4 mm Type Output shaft thread M12 Multi 255-3 (Ø 255 3 teeth) Grass blade/grass cutter Multi 275-4 (Ø 275 4 teeth) Multi 300-3 (Ø 300 3 teeth) Saw blade Plastic blades Maxi XS 200-22 (Ø 200 22 teeth) Scarlet 200-22 (Ø 200 22 teeth) Tricut Ø 300 mm Trimmy S II Trimmer head Auto 55 T45x Support cup Shredder blade Fixed With ball bearing 544 02 65-02 537 28 85-01 537 28 85-01 537 28 85-01 537 31 09-01 537 31 09-01 537 28 85-01 503 95 43-01 503 95 43-01 503 95 43-01 Cutting attachment guard, Art. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 343 F




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 343 F will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.