User manual HUSQVARNA 326 C

[. . . ] Operator's manual (CARB II, EPA II) 326C 326L 326LX-SERIES 326LDX-SERIES Please read these instructions carefully and make sure you understand them before using the machine. English SYMBOL EXPLANATION Symbols WARNING!Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. Always use • A protective helmet where there is a risk of falling objects • Ear protection • Approved eye protection Always wear approved protective gloves. Use anti-slip and stable boots. Only use non-metallic, flexible cutting elements, that is trimmer head with trimmer cord. Only intended for the trimmer head. max 10000 rpm Max. [. . . ] The bevel gear unit can get hot during use and may remain so for a while afterwards. Children, animals, onlookers and helpers should be kept outside the safety zone of 15 m (50 feet). Stop the machine immediately if anyone approaches. 10 – English WHAT IS WHAT? What is what on the trimmer? 1. Trimmer head Grease filler cap Angle gear Spray guard Shaft Loop handlebar Throttle Stop switch Throttle trigger lock Cylinder cover Starter handle Fuel tank Choke 14. Air purge Air filter cover Clutch cover Handlebar adjustment Locking nut Support flange Drive disc Socket spanner Operator‘s Manual Allen key Locking pin Shaft coupling English – 11 ASSEMBLY Assembling the loop handlebar (326C) • Position the handle on the shaft. • Fit the bolt, securing plate and wing nut as shown in the diagram. • Tighten the wing nut. Assembling and dismantling the two-part shaft (326LDX) Assembling: • Make sure the handle is loose. • Guide the cut-out on the lower section of the shaft into the coupling‘s locking plate on the upper section of the shaft. • Tighten the handle. Dismantling • Undo the handle (at least three turns). • Carefully twist the lower section out of the lock. Assembling the loop handlebar (326L, 326LX, 326LDX) • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. Tighten the bolt/ knob. • Hold both parts of the shaft and pull out the lower section from the coupling. Assembly of the trimmer head It is extremely important that the disc drive’s/support flange’s guide engages correctly in the cutting equipment’s centre hole when assembling the cutting equipment. Cutting equipment assembled incorrectly can result in serious and/or fatal personal injury. ! 12 – English WARNING!Under no circumstances may the cutting equipment be used without an approved guard fitted. If the wrong guard or a defective guard is fitted this can cause serious personal injury. ASSEMBLY Assembling the spray guard and trimmer head Superauto II (326L, 326LX, 326LDX) • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. • Insert the locking pin (C) in the hole so that the axle is locked. Proceed as follows: • Insert your finger into the centre hole of the cover (I) at the same time as you hold the cover with your other fingers. Press the two catches (J) that extend from the cut-out on the bottom section (K) using the thumb and index finger of your other hand. • Place the cover (I) and the support flange (F) on the output axle. Hold the handle of the spanner as close to the trimmer guard as possible. [. . . ] Normally, the grease does not need to be changed except when repairs are carried out. English – 19 TECHNICAL DATA Technical data Engine Displacement, cu. to ISO 8893 Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm Fuel lubrication system Manufacturer/type of carburetor Fuel tank capacity, US pint/litres Weight Weight without fuel, cutting tool and guard, Lbs/kg 326C 1, 50/24, 5 1, 32/34 1, 06/27 11 000 - 11 700 2 700 11 700 0, 9 kW/ 8400 rpm Yes - 326L 1, 50/24, 5 1, 32/34 1, 06/27 11 000 - 11 700 2 700 8 014 0, 9 kW/ 8400 rpm Yes Yes 326LX/326LDX 1, 50/24, 5 1, 34/34 1, 06/27 11 000 - 11 700 2 700 8 014 0, 9 kW/ 8 400 rpm Yes Yes Walbro MB Champion RCJ 6Y 0, 02/0, 5 Walbro MB Champion RCJ 6Y 0, 02/0, 5 Walbro MB Champion RCJ 6Y 0, 02/0, 5 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 9, 5/4, 3 9, 0/4, 1 LX: 9, 7/4, 4 LDX: 9, 9/4, 5 Sound levels (See note 1) Equivalent sound pressure level at the user’s ear, measured according to ANSI B175. 3-1997, dB(A), min/max: Vibration levels Vibration levels on the handles, measured according to ANSI B175. 3-1997, m/s2 When idling, left/right handles, min: When idling, left/right handles, max: At max. speed, left/right handles, max: 91/98 91/97 91/97 2, 7/1, 5 3, 5/1, 7 4, 4/4, 8 5, 7/5, 7 1, 7/1, 5 2, 7/1, 8 3, 9/5, 2 7, 2/9, 8 1, 7/1, 5 2, 7/1, 8 3, 9/5, 2 7, 2/9, 8 Note 1: Equivalent sound pressure level is calculated as the time-weighted energy total for sound pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max speed. Sound pressure at the user's ear and vibration on the handles are measured with all the machine's approved cutting equipment fitted. [. . . ]