User manual HUSQVARNA 323 C 325 CX

[. . . ] Operator’s manual (EPA) 323C 325CX 323L 325LX 325LDX Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. English KEY TO SYMBOLS Symbols WARNING!Careless or incorrect use can result in serious or fatal injury to the operator or others. Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. Always wear: • • • A protective helmet where there is a risk of falling objects Hearing protection Approved eye protection Always wear approved protective gloves. [. . . ] Tighten the knob. • Dismantling: • • • Fit the screw, securing plate and wing nut as shown in the diagram. Undo the knob (at least three turns). Fitting the loop handle (323L, 325Lx, 325LDx) • • • Push the knob towards the coupling. Hold both parts of the shaft and pull the lower part of the shaft out of the coupling. • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. Fitting the trimmer head When fitting the cutting attachment it is extremely important that the raised section on the drive disc/support flange engages correctly in the centre hole of the cutting attachment. If the cutting attachment is fitted incorrectly it can result in serious and/or fatal personal injury. • • Slide the spacer into the slot in the loop handle. Do not overtighten. • Now adjust the trimmer to give a comfortable working position. Tighten the bolt/knob. Assembling and dismantling the two-piece shaft (325LDx) ! WARNING!If an incorrect or faulty guard is fitted this can cause serious personal injury. Assembly: • Make sure the knob is loose. 12 – English ASSEMBLY Fitting a trimmer guard and Superauto II trimmer head (323L, 325Lx, 325LDx) Fitting other guards and cutting attachments (323L, 325Lx, 325LDx) • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (L). K J I G F I B C K A • Fit the correct trimmer guard (A) for use with the trimmer head. Hook the guard onto the fitting on the shaft and secure it with the bolt (L). Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. To fit the trimmer head, first separate the two halves (see diagram). Proceed as follows: Insert a finger into the centre hole of the cover (I) while grasping the cover with your other fingers. Using the index finger and thumb of your other hand, release the two catches (J) that engage in the cut-outs in the bottom half (K). Hold the shaft of the spanner as close to the blade guard as possible. To tighten the nut, turn the spanner in the opposite direction to the direction of rotation (left-hand thread). • • • • • A • • • • • Fit the drive disc (B) on the output shaft. Turn the blade shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. Screw on the trimmer head/plastic blades (H) in the opposite direction to the direction of rotation. H H • • To dismantle, follow the instructions in the reverse order. • Fit the bottom half of the trimmer head (K) to the cover (I) by pressing them together, with the cut-outs on the bottom half aligned with the catches on the cover. • To dismantle, follow the instructions in the reverse order. English – 13 ASSEMBLY Fitting the trimmer guard and trimmer head (323C) Fitting the trimmer guard and trimmer head (325Cx) Guard • Fit the guard as shown in the diagram. Tighten securely. • Insert the locking pin into the hole to lock the axle. Trimmer head • • • Fit the dust cup on the shaft. Screw the trimmer head onto the shaft. • Screw the trimmer head onto the shaft. 14 – English FUEL HANDLING Fuel CAUTION!The machine is equipped with a two-stroke engine and must always been run using a mixture of gasoline and two-stroke engine oil. [. . . ] to ISO 8893, kW/ r/min Catalytic converter muffler Speed-regulated ignition system Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, inch/mm Fuel and lubrication system Manufacturer/type of carburettor Fuel tank capacity, US pint/litre Weight Weight without fuel, cutting attachment and guard, Lbs/kg 9, 0/4, 1 Sound levels (see note 1) Equivalent sound pressure level at the user′s ear, measured according to ANSI B175. 3-1997, dB(A), min/ 92/98 max: Vibration levels Vibration levels at handles, measured according to ANSI B175. 3-1997, m/s2 At idle, left/right handles, min. : At idle, left/right handles, max. : At max. speed, left/right handles, max. : 1, 5/1, 4 2, 0/1, 8 2, 5/4, 8 4, 9/8, 0 1, 5/1, 4 2, 4/2, 2 2, 5/4, 8 5, 8/7, 6 90/98 9, 7/4, 4 Zama C1Q 1, 06/0, 5 Zama C1Q 1, 06/0, 5 WalbroMB/SEM AM49 Champion RCJ 7Y 0, 02/0, 5 WalbroMB/SEM AM49 Champion RCJ 7Y 0, 02/0, 5 1, 50/24, 5 1, 34/34 1, 06/27 2700 11000-11700 8014 0, 9/9000 Yes No 1, 50/24, 5 1, 34/34 1, 06/27 2700 10000-10500 8014 0, 9/9000 Yes Yes 325Lx 325LDx Note 1: Equivalent noise pressure level is calculated as the time-weighted energy total for noise pressure levels under various working conditions with the following time distribution: 1/2 idle and 1/2 max. Noise pressure at the user’s ear and vibration on the handles are measured with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. 24 – English TECHNICAL DATA 323C Approved accessories Blade shaft thread 3/8 R Trimmer head Trimmy Hit Junior (R) Trimmy Fix 3/8” (R) Trimmy Hit VII (R) 537 02 61-01 537 02 61-01 537 02 61-01 Type Cutting attachment guard, Art. [. . . ]