User manual HUSQVARNA 322 C

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual HUSQVARNA 322 C. We hope that this HUSQVARNA 322 C user guide will be useful to you.


HUSQVARNA 322 C : Download the complete user guide (1879 Ko)

Manual abstract: user guide HUSQVARNA 322 C

Detailed instructions for use are in the User's Guide.

[. . . ] 322C 322L 325L 325L X-SERIES Operator's manual 325L XT-SERIES 325C 325C X-SERIES (EPA) Read through the Operator‘s Manual carefully and understand the content before using the machine. 101 91 71-95 SYMBOL EXPLANATION Symbols WARNING!Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. • Always wear approved protective gloves. • Use anti-slip and stable boots. • Only use non-metallic, flexible cutting elements, that is trimmer head with trimmer cord. Always use • A protective helmet where there is a risk of falling objects • Ear protection • Approved eye protection • Only intended for the trimmer head. max 10000 rpm • Max. [. . . ] • Tighten the wing nut. Assembling and dismantling the two-part shaft (325L-XT) Assembling: • Make sure the handle is loose. • Guide the cut-out on the lower section of the shaft into the coupling‘s locking plate on the upper section of the shaft. • Tighten the handle. Dismantling • Undo the handle (at least three turns). • Hold both parts of the shaft and pull out the lower section from the coupling. Assembling the loop handlebar (322L, 325L-X/L-XT) • Clip the loop handle onto the shaft. Note that the loop handle must be fitted between the arrows on the shaft. Tighten the bolt/knob. Assembly of the trimmer head It is extremely important that the disc drive’s/support flange’s guide engages correctly in the cutting equipment’s centre hole when assembling the cutting equipment. Cutting equipment assembled incorrectly can result in serious and/or fatal personal injury. ! 12 – English WARNING!Under no circumstances may the cutting equipment be used without an approved guard fitted. If the wrong guard or a defective guard is fitted this can cause serious personal injury. ASSEMBLY Assembling the spray guard and trimmer head Superauto II (322L, 325L-X/L-XT) • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Turn the blade axle until one of the holes in the drive disc aligns with the hole in the gear housing. • Insert the locking pin (C) in the hole so that the axle is locked. Proceed as follows: • Insert your finger into the centre hole of the cover (I) at the same time as you hold the cover with your other fingers. Press the two catches (J) that extend from the cut-out on the bottom section (K) using the thumb and index finger of your other hand. • Place the cover (I) and the support flange (F) on the output axle. Hold the handle of the spanner as close to the trimmer guard as possible. The nut is tightened when the spanner is turned against the direction of rotation (left-hand thread). • Fit the trimmer head‘s bottom section (K) on the cover (I) by pressing the two sections together with the cut-outs on the bottom section aligned with the catches on the cover. • To dismantle follow the instructions in the reverse order. Assembling other guards and cutting equipment (322L, 325L-X/L-XT) • Fit the appropriate guard (A) for use with the trimmer head. Hook the guard onto the shaft fitting and secure it with the bolt (L). • Turn the blade axle until one of the disc drive’s holes aligns with the corresponding hole in the gear housing. • Insert the locking pin (C) into the hole to lock the axle. H K J I • Screw on the trimmer head (H) in the direction of rotation. [. . . ] Noise and vibration measurements are made with all the machine’s approved cutting equipment fitted. The table indicates the highest and lowest values. Approved accessories Thread blade shaft 3/8 (R) Plastic knifes Trimmer head Type Tricut ∅ 230 mm (R) Trimmy Hit VI (R) Trimmy Fix (R) Trimmy Hit Junior (R) Cutting attachment guard Art No. 537 07 67-01 537 07 67-01 537 07 67-01 537 07 67-01 22 – English EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 1999 and later small nonroad engine. In U. S. , new small nonroad engines must be designed, built and equipped to meet the federal stringent anti-smog standards. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE HUSQVARNA 322 C




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual HUSQVARNA 322 C will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.