User manual HUSQVARNA 245 R

[. . . ] Operator's manual (EPA) 240R 245R/RX 250R 252RX 265RX Please read these instructions carefully and make sure you understand them before using the machine. English SYMBOL EXPLANATION Symbols WARNING!Careless or incorrect use can result in serious or fatal injury to the operator or others. Read through the Operator‘s Manual carefully and understand the content before using the machine. • Only use non-metallic, flexible cutting elements, that is trimmer head with trimmer cord. [. . . ] • Reduce the risk of damaging plants by shortening the cord to 10-12 cm and reducing the engine speed. Clearing • The clearing technique removes all unwanted vegetation. Let the end of the cord strike the ground around trees, posts, statues and the like. • The cord wears quicker and must be fed forward more often when working against stones, brick, concrete, metal fences, etc. • When trimming and clearing you should use less than full throttle so that the cord lasts longer and to reduce the wear on the trimmer head. Trimming • The trimmer is ideal to cut grass that is difficult to reach using a normal lawn mower. Avoid pressing the trimmer head against the ground as this can ruin the lawn and damage the tool. • Do not allow the trimmer head to constantly come into contact with the ground during normal cutting procedures. Constant contact can cause damage and wear to the trimmer head. Sweeping • The rotating cord‘s fanning effect can be used for quick and easy cleaning. Hold the cord parallel to and above the area to be swept and move the trimmer from side to side. • When cutting and sweeping you should use full throttle to obtain the best results. ! WARNING!can be thrown up into the eyes resulting in blindness or other serious injury. Children, animals, onlookers and helpers should be outside the safety zone of 15 meters (50 feet). Stop the machine immediately if anyone approaches. 16 – English WHAT IS WHAT? 240R, 245R 2 3 5 6 7 17 8 9 14 10 13 11 12 26 33 18 20 19 1 22 21 4 27 21 32 31 29 30 25 28 What is what on the trimmer/brushcutter?Locking nut 17 WHAT IS WHAT? 245RX 2 3 8 5 7 17 9 10 13 14 11 12 26 6 18 19 1 21 27 4 25 28 29 30 31 What is what on the trimmer/brushcutter?Harness 18 – English WHAT IS WHAT? 250R 1 3 7 8 9 26 2 33 4 18 20 19 1 21 4 29 32 25 5 16 15 14 6 17 10 11 12 31 30 27 28 What is what on the clearing saw?Locking nut 19 WHAT IS WHAT? 252RX 1 3 8 7 5 2 9 26 17 10 11 12 4 18 6 19 1 21 4 32 29 25 16 15 14 31 30 28 27 What is what on the clearing saw?Gearbox grease WHAT IS WHAT? 265RX 1 3 7 5 17 8 9 10 14 15 11 13 12 2 18 19 31 1 21 4 27 26 25 29 32 6 30 28 What is what on the clearing saw?Gearbox grease English – 21 ASSEMBLY Assembling the handlebars (240R, 245R, 250R) • Remove the screw at the rear of the throttle handle. • Slide on the throttle handle on the right-hand side of the handlebars, (see the diagram). • Align the hole in the throttle handle for the fixing screw with the hole on the handlebars. • Fit the screw through the throttle handle and the handlebars and tighten. [. . . ] to ISO 8893 Muffler fitted with catalytic converter Ignition system Manufacturer/type of ignition system Spark plug Electrode gap, mm Fuel lubrication system Manufacturer/type of carburettor Fuel tank capacity, litres Weight Weight without fuel, cutting tool andguard, kg Noise levels Equivalent noise pressure level at the user’s ear, measured according to prEN 31806 and ISO 7917, dB(A), min/max: Equivalent noise power level at the user’s ear, measured according to prEN 31806 and ISO 10884, dB(A), min/max: Vibration levels Vibration levels on the handles, measured according to prEN 31806 and ISO 7916, m/s When idling, left/right handles, min: When idling, left/right handles, max: At max. speed, left/right handles, max: 250R 48, 7 44 32 2 700 12 500 9 190 2, 1 kW/9 000 rpm No 252RX 50, 8 45 32 2 700 14 000 10 300 2, 4 kW/9 000 rpm No 265RX 65, 1 48 36 2 250 11 500 9 120 3, 0 kW/8 400 rpm No EM/ET Champion RCJ 7Y 0, 5 EM/ET Champion RCJ 7Y 0, 5 SEM GA 6CD Champion RCJ 7Y 0, 5 Walbro HDA 0, 8 Walbro HDA 0, 8 Tillotson HS 1, 0 9, 2 8, 9 10, 8 98/104 96/103 98/100 110/113 110/111 112/113 3, 4/3, 9 4, 4/4, 0 1, 2/1, 7 2, 2/2, 6 2, 8/2, 8 4, 5/3, 9 1, 2/1, 4 1, 6/1, 7 4, 5/4, 0 5, 1/4, 6 3, 0/3, 9 3, 9/5, 1 NOTE!The noise and vibration measurments are made with all for the machine approved cutting equipment. The maximum and minimum values are stated in the table above. 36 – English TECNICAL DATA Approved accessories 240R, 245R/RX Centre hole in saw blades/knives, ∅ 20 mm Thread output axle M12 Grass blade/grass knife Type Cutting attachment guard Art No. Saw blade Plastic knives Trimmer head Support cup Multi 255-3 (∅ 255 3-teeth) Multi 275-4 (∅ 275 4-teeth) Multi 300-3 (∅ 300 3-teeth) Maxi XS 200-22 (∅ 200 22-teeth) Tricut ∅ 300 Trimmy S Trimmy S II Fixed With ball bearing 502 12 26-01 502 26 34-01 502 26 34-01 502 27 22-01 503 91 60-01/502 26 34-01 503 91 60-01 503 91 60-01 - Approved accessories 250R Centre hole in saw blades/knives, ∅ 20 mm Thread output axle M12 Grass blade/grass knife Type Cutting attachment guard Art No. Saw blade Plastic knives Trimmer head Support cup Multi 255-3 (∅ 255 3-teeth) Multi 275-4 (∅ 275 4-teeth) Multi 300-3 (∅ 300 3-teeth) Maxi XS 200-22 (∅ 200 22-teeth) Maxi XS 225-22 (∅ 200 22-teeth) Tricut ∅ 300 Trimmy S Trimmy S II With ball bearing 502 12 26-01 502 26 34-01 502 26 34-01 502 27 22-01 502 03 94-03 503 91 60-01/502 26 34-01 503 91 60-01 503 91 60-01 - Approved accessories 252RX Centre hole in saw blades/knives, ∅ 20 mm Thread output axle M12 Grass blade/grass knife Type Cutting attachment guard Art No. Saw blade Trimmer head Support cup Multi 255-3 (∅ 255 3-teeth) Multi 275-4 (∅ 275 4-teeth) Multi 300-3 (∅ 300 3-teeth) Maxi XS 200-22 (∅ 200 22-teeth) Maxi XS 225-22 (∅ 200 22-teeth) Trimmy S Trimmy S II With ball bearing 502 12 26-01 502 26 34-01 502 26 34-01 502 27 22-01 502 03 94-03 503 91 60-01 503 91 60-01 - Approved accessories 265RX Centre hole in saw blades/knives, ∅ 20 mm Thread output axle M12 Grass blade/grass knife Saw blade Type Cutting attachment guard Art No. Trimmer head Support cup Multi 300-3 (∅ 300 3-teeth) Maxi XS 200-22 (∅ 200 22-teeth) Maxi XS 225-22 (∅ 200 22-teeth) Opti 255-22 (∅ 255 22-teeth) Trimmy S Trimmy S II With ball bearing 502 26 34-01 502 27 22-01 502 03 94-03 502 03 95-03 503 91 60-01 503 91 60-01 - English – 37 EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 1999 and later small nonroad engine. [. . . ]