User manual HUSQVARNA 141

[. . . ] It should be read and used by any person installing or using the machine. The instructions for use and spare parts found in this document are for information only and are not binding. As part of our product quality improvement policy, we reserve the right to make any and all technical modifications without prior notice. 1 - Frame 2 - Table 3 - Swivelling wheel 4 - Water tank 5 - Fixed wheel 6 - Handwheel of the head advance 7 - Emergency stop 8 - Star / Triangle commutator 9 - Start / Stop switch 10 - Protective curtains 11 - Handwheel of the plunging head 12 - Head blocking lever 13 - Motor 14 - Belt guard 15 - Blade guard 16 - Water pump 17 - Operating key 18 - Sling eye 19 - Cutting guide 20 - Water tank blocking bar 21 - Transportation slots Blade (mm) Depth of cutting (mm) Net weight (kg) Using weight (kg) Dimensions (L x l x H - mm) Shaft RPM Motor RPM Power (CV/kW) Voltage (V) Amps (A) Electrical protection Max width (Right - mm) Max width (Left ­ mm) Water tank volume (litre) Bore of the blade (mm) 900 / 1000 310 / 360 324kg 440 kg 1950 x 970 x 1700 1100 1430 12 / 9 400 (3 phases) 18, 5 IP54 260 450 95 60 Noise ­ Pressure level According to ISO 5489 Aeq (m/s²), No cutting Aeq (m/s²), during cutting 1, 15 NC The manufacturer declines any liability resulting from misuse or modification of the saw. [. . . ] In particular, the following points must be regularly verified at the worksite: · Perfect technical conditions (saw used for suitable jobs considering potential risks; elimination of any malfunctions jeopardizing safety), use of a diamond disk for water sawing (cutting fresh, old or coated concrete, asphalt); use of any other type of disk (eg abrasive, saw) is strictly forbidden competent personnel (qualification, age, training, skill), who understand the manual in detail before starting work. Any electrical, mechanical or other defect or failure is to be inspected by an authorized service expert (eg electrician, maintenance manager, official dealer) observance of all warnings and directives marked on the machine (eg use of personal protective equipment); users must follow all instructions and comply with all safety rules no modification, transformation or addition that could potentially effect safety may be performed without the manufacturer's express authorization periodic inspections must be carried out as specified, at the intervals specified original manufacturer's spare parts must be used for any repairs. DO use only discs marked with a maximum operating speed greater than that of the disk shaft exercise all due care and follow all instructions when loading and unloading saw. DON'T allow other people nearby when starting the saw, refueling or cutting run gasoline (petrol) motors in a confined space without appropriate ventilation use damaged equipment or disks operate the saw in the vicinity of flammable products. Authorize disc protection under 108° C leave saw unattended with motor running. DO carefully read and make sure that you have understood all instructions before using the saw. Keep all safety guards in place always wear approved ear, eye, head and respiratory protective equipment always keep a safe distance from the disc and other moving parts know how to stop the saw fast in case of emergency. Before starting, read the instructions carefully and get familiar with the machine. Verify the following: ELECTRICAL SAFETY: Must be connected to power source using a grounded 30mA residual differential current circuit-breaker. Should their be no such circuit breaker on the power supply network, please see our catalogue for different models available. For tools with an RDC system built into the electrical cord or plug: should the cord or plug become damaged, repairs may be performed only by the manufacturer, their authorized agent or a qualified repair shop in order to avoid any hazard due to improper repair. Store products in a safe and secure place, out of the reach of children. After a certain amount of use, it may be necessary to restretch the belt. 6] Turn tension screw (L) one quarter turn to pull back the motor When tension is normal, re-tighten four screws (K) on motor Dispose of used lubricants according to legislation in force. For extremely dusty conditions, the filter element may have to be cleaned up to three times a day. Clean machine after each use Frequently empty the pan to remove saw sludge that may clog the water pump or wear it out prematurely Swill out pan with water Frequently clean the working areas of the head and table castors Periodically add bearing grease to guide castor grease fittings (J) [FIG. Periodically re-tighten hardware, especially after first hours of operation Check belt tension but never over-tighten When storing saw, remove disc and store carefully Make sure that disc is kept wet by regularly inspecting water injectors. The manufacturer declines any liability resulting from any misuse, modification or adaptation of the saw or from use of a motor that does not correspond to the manufacturer's original specifications In case of malfunction see the table below for a solution to problems encountered. The machine doesn't work: CAUSES Bad or damaged power cord SOLUTIONS - Check that machine is properly plugged in (ie check plug and any extension cord) - Check power cord - Have electrician check electrical outlet, circuit breakers. To save time and ensure rapid delivery of spare parts, please make sure your order includes the details on the machine information plate as well as the reference of the replacement part. DURATION This guarantee is valid for six months effective from the date of purchase by the user (date on the retailer's bill). SCOPE The guarantee is limited to free replacement of parts having manufacturing defects recognized by Dimas (except for wearing parts and consumables) if repairs are performed in a workshop operated or approved by Dimas. [. . . ] SCOPE The guarantee is limited to free replacement of parts having manufacturing defects recognized by Dimas (except for wearing parts and consumables) if repairs are performed in a workshop operated or approved by Dimas. The manufacturer will not be held accountable for any direct or indirect material damages or consequential losses caused by persons or things following failure or stoppage of the machine. CONDITIONS OF GUARANTEE To be entitled to the guarantee, the user must return the certificate of guarantee duly completed to Dimas within eight days of purchase. Should a problem occur during the guarantee period, our customer service department will tell you of the best way to solve it and, if necessary, inform you of the closest approved service center. [. . . ]