User manual HUSQVARNA 130 BT

[. . . ] 130BT&180BT_US-65. fm Page 1 Friday, December 7, 2007 1:05 PM WARNING The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects or other reproductive Operator’s manual WARNING Before using our products, please read this manual carefully to understand the proper use of your unit. APPLICABLE SERIAL NUMBERS: 80100101 and up 130BT 150BT/BF 170BT/BF 180BT/BF English 115 09 83-95 130BT&180BT_US-65. fm Page 2 Friday, December 7, 2007 1:05 PM English FEDERAL EMISSION CONTROL WARRANTY STATEMENT YOUR WARRANTY RIGHTS AND OBLIGATIONS The EPA (The US Environmental Protection Agency), CARB (California Air Resources Board), Environment Canada and Husqvarna Forest & Garden are pleased to explain the emissions control system warranty on your 2007 and later small nonroad engine. and Canada, new small nonroad engines must be designed, built and equipped to meet the federal stringent antismog standards. Husqvarna Forest & Garden must warrant the emission control system on your small nonroad engine for the period of time listed below provided there has been no abuse, neglect or improper maintenance of your unit. [. . . ] Frame: Harness: Throttle lever: Volute case, Volute cover, Engine cover: Pad: Flexible hose: Pipes: Fan: Element: PE (Polyethylene) Chemical fiber Metal, Plastic PA66GF (Glass-reinforced nylon), Brass Chemical fiber EVA (Ethylene vinyl acetate) PP (Polypropylene) PA66GF (Glass-reinforced nylon) Paper, Urethane DISPOSAL * The insert nut of volute case, volute cover and fan can be taken off. 11 130BT&180BT_US-65. fm Page 12 Friday, December 7, 2007 1:05 PM English What is what? <180BT/BF> 2 1 22 15 11 13 12 16 19 20 14 4 <180BT> 8 18 3 9 17 6 10 7 21 <180BF> 1. 23. Recoil Starter Stop Switch with Throttle Position Setting Engine Cover Handle Bar (Option) (180 BT only) Fan Shock Absorber (Rubber) Flexible Hose Pipes Pad Flat Nozzle (Option) “EMISSION” Label When disposing your machine, fuel or oil for the machine, be sure to allow your local regulations. Frame: Harness: Throttle lever: Volute case, Volute cover, Engine cover: Pad: Flexible hose: Pipes: Fan: Element: ABS Chemical fiber Metal, Plastic PA66GF (Glass-reinforced nylon), Brass Chemical fiber EVA (Ethylene vinyl acetate) EVA (Ethylene vinyl acetate) PA66GF (Glass-reinforced nylon) Paper, Urethane DISPOSAL * The insert nut of volute case, volute cover and fan can be taken off. 12 130BT&180BT_US-65. fm 13 ページ ２００８年３月２１日　金曜日　午後１時６分 English Technical data MODEL 130BT 150BT 150BF 170BT 170BF 180BT 180BF Dimensions (L x W x H) 295x387x432 351x446x479 351x487x479 365x464x485 365x496x485 410x509x497 410x550x497 mm (in) (11. 6x15. 2x17) (13. 8x17. 6x18) (13. 8x19. 2x18) (14x18x19) (14x20x19) (16. 1x20x19. 6) (16. 1x21. 7x19. 6) Dry Weight kg (lbs) (including pipe) Dry Weight kg (lbs) (without accessories) 6. 75 (14. 9) 10. 2 (22. 5) 10. 4 (22. 9) 6. 1 (13. 4) 9. 5 (20. 9) 1. 25 (42. 3) 12 (26. 5) 12. 2 (26. 9) 13. 2 (29. 1) 13. 4 (29. 5) 11. 2 (24. 7) 1. 75 (60. 0) 12. 4 (27. 3) 2. 13 (72. 0) Fuel Tank Capacity liter 0. 9 (30. 4) (fl. in) Air Filter Carburetor (Diaphragm) valve type Ignition System Spark Plug Muffler Idle speed rpm Operating Engine Speed rpm Fuel Consumption liter/h (fl. oz/h) 3000 3000 to 6700 0. 58 (19. 6) CDI 29. 5 (1. 8) Single stage filter Air cooled 2-cycle gasoline engine 50. 2 (3. 1) Single stage filter (half wet) Rotary Digital Ignition NGK CMR7H Spark arrester equipped 2200 2200 to 6100 1. 04 (35. 2) 14 (494) 19. 6 (692) 80 (180) 71 104 2000 to 6900 1. 6 (54. 1) 16 (565) 21. 0 (742) 88 (198) 76 110 2000 2000 to 6700 1. 85 (62. 6) 19. 4 (685) 25. 9 (915) 90 (201) 77 109 64. 9 (4. 0) 71. 9 (4. 4) 2-stage fresh flow filter system Average Air Volume (w/std 10. 2 (360) Pipe) cu. m/min (cf/m) Air velocity m/sec (mph) (Maximum) Noise Level (50 Feet ANSI B175. 2-2000) dB(A) Sound power level EC directive 2000/14/ EC, measured dB (A) Sound power level EC directive 2000/14/ EC, guaranteed dB (A) Noise pressure level at the operator’s ear (LpAeq) prEN15503 (ISO7917) dB (A) Vibration level at idle, right handle prEN15503 (ISO7916) m/s2 Vibration level at max, speed, right handle prEN15503 (ISO7916) m/s2 65 (145) 69 102 102 104 110 90 94 95 (ISO7917) 0. 8 (ISO7916) 3. 9 (ISO7916) 1. 4 (ISO7916) 4. 3 (ISO7916) 100 1. 9 2. 9 2. 3 2. 2 2. 6 2. 6 2. 1 2. 5 3. 5 4. 5 • The data shown above are those in the case of one straight pipe. • Specifications are subject to change without notice. 13 130BT&180BT_US-65. fm Page 14 Friday, December 7, 2007 1:05 PM English Assembly 1. Clamp both ends of the flexible hose securely with the hardware supplied with the unit. NOTE SWIVEL JOINT F1 A light lubricant may be used to ease assembly of flexible hose to blower elbow. 1. Set up the throttle holder to the swivel and tighten the screw on the holder. THROTTLE LEVER [130BT/150BT/170BT/180BT] F2 (2) When setting up the holder, please make sure to match the holder to the convex on the swivel joint as shown in F2. Adjust the position and angle to achieve a comfortable working position, and tighten the throttle lever. (1) Cable (2) Hose [130BT] • Fasten the throttle cable at central position of the hose by the band attached to the throttle cable. First, wrap the hose with the band fixed to the throttle cable from the lower side. Please note that there is a possibility of damaging the hose if the band is fastened too tightly. [150BT] [170BT] [180BT] • Use the clamp to fasten the colgate tube containing the throttle cable and the power cable to the hose. (1) Clamp (1) (1) THROTTLE CABLE [130BT/150BT/170BT/180BT] F3 [130BT] F4 [150BT] [170BT] [180BT] • Insert the handle holder to the swivel and tighten the screw on the holder. When setting up the holder, please make sure to match the holder to the convex on the swivel joint as shown in F5. RIGHT HANDLE [150BF/170BF/180BF] F5 1. Insert the holder, then assemble the handlebar (OPTION) and tighten it securely. HANDLEBAR [OPTION] [130BT/150BT/170BT/ 180BT] F6 14 130BT&180BT_US-65. fm 15 ページ ２００８年３月２１日　金曜日　午後１時６分 English Assembly 1. Align the protrusion and the groove provided on the tube ends and twist the tube until the connection is locked. NOTE BLOWER TUBES F7 A light lubricant may be used to ease assembly of blower tube. NOTE If longer tube is required, the second straight pipe can be connected with the first one. If higher air speed is required, the round blow pipe can be replaced by the flat nozzle with the second straight pipe. (1) Flat nozzle (option) F8 (1) HARNESS NOTE The harness must always be worn when working with the machine. Failure to do so means you will be unable to maneuver safely and this can result in injury to yourself or others. A correctly adjusted harness and machine significantly facilitates the work. [. . . ] Disconnect the filter assembly from the fuel pipe and unhook the retainer to disassemble it. (1) Screen (3) Holder (2) Element (x 2) (4) Retainer FUEL FILTER F32 • The spark plug may gather carbon deposits on its firing end with reasonable use. Remove and inspect the spark plug every 25 hours and clean the electrodes as necessary with a wire brush. • Plug manufacturers recommend replacing the plug twice a year to avoid unexpected plug failure in a job. [. . . ]