User manual HUSQVARNA 128CD

[. . . ] 5 Checking, maintaining and servicing the machine’s safety equipment . 24 Category C = 50 hours, B= 125 hours, and A = 300 hours. For reference, please fill out the following information that will be needed for future servicing of your trimmer: Model Number: Serial Number: Purchase Date: Purchased From: WARNING: A clearing saw, brushcutter or trimmer can be dangerous if used incorrectly or carelessly, and can cause serious or fatal injury to the operator or others. It is extremely important that you read and understand the contents of this operator’s manual. WARNING: Under no circumstances may the design of the machine be modified without the permission of the manufacturer. [. . . ] 1 9/15/09 English--- 12 ASSEMBLY NOTE: Make sure unit is assembled correctly as shown in this manual. Dismantling: Fitting the loop handle S Loosen the coupling by turning the knob. S Position the handle on the upper shaft. Note that the handle must be mounted between the two arrows on the shaft. S While securely holding the engine and upper shaft, pull the attachment straight out of the coupling. S Tighten the wing nut. Assembling and dismantling the two-piece shaft Fitting the trimmer guard and Assembly: S Loosen the coupling by turning the knob. trimmer head (Model 128LD) S Position locking/release button (A) of attachment into guide recess (B) of coupling. A B S Push the attachment into the coupling until the locking/release button snaps into the primary hole (C). S Fit the correct trimmer guard (D) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the bolt (E). E F G C S Before using the unit, tighten the knob securely. D D S Fit the drive disc (F) on the output shaft. S Turn the shaft until one of the holes in the drive disc aligns with the corresponding hole in the gear housing. S Screw on the trimmer head (H) in the opposite direction to the direction of rotation. H WARNING: All attachments are designed to be used in the primary hole unless otherwise stated in the applicable attachment instruction manual. Using the wrong hole could lead to serious injury or damage to the unit. S To dismantle, follow the instructions in the reverse order. 1 9/15/09 ASSEMBLY Fitting the trimmer guard and trimmer head (Model 128CD) S Fit the correct trimmer guard (A) for use with the trimmer head. Hook the trimmer guard/combination guard onto the fitting on the shaft and secure with the wing nut (B). S Screw the trimmer head (D) onto the shaft. D S To dismantle, follow the instructions in the reverse order. 115275126 Rev. The machine is equipped with a two-stroke engine and must always be run using a mixture of gasoline and twostroke engine oil. It is important to accurately measure the amount of oil to be mixed to ensure that the correct mixture is obtained. When mixing small amounts of fuel, even small inaccuracies can drastically affect the ratio of the mixture. S Mix (shake) the fuel mixture thoroughly before filling the machine’s fuel tank. WARNING: Always ensure there is adequate ventilation when handling fuel. Gasoline S Do not mix more than one month’s supply of fuel at a time. S If the machine is not used for some time, the fuel tank should be emptied and cleaned. WARNING: The catalytic converter muffler gets very hot during and after use. Be aware of the fire hazard, especially when working near flammable substances and/or vapors. CAUTION! [. . . ] Proof of purchase, as explained in Section 6, rests solely with the customer. SECTION 4: EXCEPTIONS AND LIMITATIONS It is the Owner’s and Dealer’s responsibility to make certain that the Warranty Registration Card is properly filled out and mailed to Husqvarna. This card should be mailed within ten (10) days from the date of purchase in order to confirm the warranty and to facilitate postsale service. Proof of purchase must be presented to the authorized Husqvarna dealer in order to obtain warranty service. This proof must include date purchased, model number, serial number, and complete name and address of the selling dealer. To obtain the benefit of this warranty, the product believed to be defective must be delivered to an authorized Husqvarna dealer in a timely manner, no later than thirty (30) days from date of the operational problem or failure. An authorized Husqvarna dealer can be normally located through the “Yellow Pages” of the local telephone directory or by calling 1-800-438-7297 for a dealer in your area. 7349 Statesville Road CHARLOTTE, NC 28269 English--- 23 U. S. [. . . ]