User manual HUSQVARNA 1130 STE XP

[. . . ] 1130STE XP Owner's Manual SAFETY RULES Safe Operation Practices for Snow Throwers IMPORTANT: This machine is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury or death. • Do not operate the equipment without wearing adeLook for this symbol to point out imquate winter outer garments. It means clothing, such as scarves, which can get caught in CAUTION!!! [. . . ] 21) Use the drift cutters to cut through deep snowdrifts that are higher than the front of the snow thrower. • Loosen upper adjustment nut enough to allow drift cutter to be raised to highest position and tighten nut securely. 20 SAFETY IGNITION KEY GASOLINE FILLER CAP STORAGE POSITION DRIFT CUTTER RECOIL STARTER HANDLE FUEL SHUTOFF VALVE STARTER BUTTON POWER CORD PLUG ADJUSTMENT NUT FIG. 22 OPERATION TO START ENGINE • Be sure fuel shut-off valve is in the OPEN position. The electric starter is equipped with a three-wire power cord and plug and is designed to operate on 120 Volt A. C. WARNING: Do not use the electric starter if your house is not a 120 Volt A. C. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. NOTE: Do not use primer when starting engine with the electric starter. IMPORTANT: Do not crank engine more than five continuous seconds between each time you try to start. When the engine starts, release the starter button and slowly move the choke control to the OFF position. Disconnect the power cord from the receptacle first, then from the engine. Engine will not develop full power until it has reached normal operating temperature. WARM START - ELECTRIC STARTER Follow the steps above, keeping the choke control in the OFF position. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the OFF position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. To avoid possible freeze-up of the starter, proceed as follows: ELECTRIC STARTER 1. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. [. . . ] 954 22 30-81 5 3 2 1 13 4 1 3 11 2 1 5 4 13 3 1 2 7 8 14 15 16 21 12 22 2 3 9 10 5 3 2 3 2 4 3 7 2 5 6 43 17 42 18 32 19 20 44 21 23 2 3 41 25 26 24 34 15 29 22 27 41 33 36 31 28 30 22 35 33 37 38 39 40 26 REPAIR PARTS DRIVE SNOW THROWER - MODEL NO. NO. DESCRIPTION 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 532 14 63-15 873 80 05-00 532 15 54-15 817 49 05-08 532 18 00-17 532 18 01-34 532 17 92-70 532 19 29-07 532 18 00-82 532 18 00-65 532 18 77-14 532 18 00-66 532 17 88-07 532 18 40-80 532 17 53-44 532 18 78-57 532 17 98-31 532 18 40-78 873 93 05-00 532 17 86-13 874 76 05-14 532 08 51-79 532 18 01-35 532 18 00-81 532 17 86-95 532 17 53-41 532 17 86-21 532 17 53-40 532 18 40-77 532 18 40-76 872 27 05-05 532 17 88-79 532 18 89-09 532 18 40-75 532 18 25-04 532 19 10-80 532 15 53-77 819 11 15-07 810 04 05-00 874 95 05-12 812 00 00-12 532 15 54-15 532 17 90-95 532 18 42-06 Screw, Hex Head 5/16-18 x 3/4 Nut, Lock 5/16-18 Washer, Flat Screw, Hex Head 5/16-18 x 1/2 Bearing, Flange Shaft, Auxiliary Spacer, Plate Plate, Auxiliary Gear, Intermediate (12/58) Gear, Pinion Rod, Clutch Shaft, Long, Hex Pin, Pivot Lever, Shifter / Wheel Trunnion Bearing Assembly Bracket, Pivot, Shift Ring, Rubber Wheel Plate, Rubber Wheel Nut, Lock 5/16-18 Hub, Rubber Wheel Screw, Hex Head 5/16-18 x 7/8 Retainer, Hairpin Spring, Bias Gear, Axle (58 Teeth) Pin, Pivot Lever Plate Assembly, Drive Shaft, Axle Shaft, Short Hex Lever, Shifter Plate Bracket, Shifter Support Bolt, Carriage 5/16-18 x 5/8 Key, Square 1/4 x 1/4 x 7/8 Bearing, Flange Plate, Drive Mounting Spacer, Bearing Pulley, Traction Drive Nut, Lock 5/16-18 Washer, Flat Washer, Lock 5/16 Screw, Hex Head 5/16-18 x 3/4 Ring, Retaining Washer . 20 x 8. 5 x 2. 0 Spring, Return Pin, Roll NOTE: All component dimensions given in U. S. inches 1 inch = 25. 4 mm 27 REPAIR PARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. 954 22 30-81 30 3 28 6 17 19 4 31 29 31 16 6 2 37 43 5 11 38 41 54 44 26 45 41 35 50 52 51 44 26 11 53 49 40 12 15 42 1 14 7 18 20 6 10 21 22 23 10 21 24 25 26 27 36 32 33 39 6 55 9 8 13 6 7 34 48 11 46 47 28 47 REPAIR PARTS CHASSIS / ENGINE / PULLEYS SNOW THROWER - MODEL NO. [. . . ]