User manual HUSQVARNA 10527 SBE

[. . . ] 10527SBE Owner's Manual IMPORTANT Safe Operation Practices for Walk-Behind Snow Throwers This snow thrower is capable of amputating hands and feet and throwing objects. Failure to observe the following safety instructions could result in serious injury. WARNING: Always disconnect spark plug wire and place it where it cannot contact plug in order to prevent accidental starting when setting up, transporting, adjusting or making repairs. WARNING: This snow thrower is for use on sidewalks, driveways and other ground level surfaces. [. . . ] Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. Push the primer four (4) times if the temperature is below 15°F, or two (2) times if temperature is between 15° and 50°F. NOTE: Over priming may cause flooding, preventing the engine from starting. If you do flood the engine, wait a few minutes before attempting to start and DO NOT push the primer. When the engine starts, release the recoil starter handle and slowly move the choke control to the OFF position. Engine will not develop full power until it has reached normal operating temperature. WARM START - RECOIL STARTER Follow the steps above, keeping the choke in the OFF position. BEFORE STOPPING Run the engine for a few minutes to help dry off any moisture on the engine. To avoid possible freeze-up of the starter, proceed as follows: 13 ELECTRIC STARTER 1. Plug the other end of the power cord into a three-hole grounded 120 Volt A. C. While the engine is running, push starter button and spin the starter for several seconds. NOTE: The unusual sound made while starter is spinning will not harm the engine or starter. Disconnect the power cord from the receptacle first, then from the engine. While the engine is running, pull the recoil starter handle with rapid, full arm strokes three or four times. NOTE: The unusual sound made while pulling the recoil starter handle will not harm the engine or starter. IF RECOIL STARTER HAS FROZEN If the recoil starter has frozen and will not turn the engine, proceed as follows: 1. Grasp the recoil starter handle and slowly pull as much rope out of the starter as possible. Release the recoil starter handle and let it snap back against the starter. If the engine still fails to start, repeat the above steps or use the electric starter. SNOW THROWING TIPS • • • • Always operate the snow thrower with the engine at full throttle. It is easier and more efficient to remove snow immediately after it falls. At this time the snow is usually dry and has not been exposed to the direct sun and warming temperatures. Slightly overlap each successive path to ensure all snow will be removed. [. . . ] 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 57 58 DESCRIPTION 4 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 532 18 10-44 Spring, Traction Idler 532 18 05-22 Pulley, Idler (2-1/4) --Engine, Tecumseh, Model Number LH358SA (For engine service and replacement parts, call Tecumseh Products at 1-800-558-5402) 874 78 05-20 Screw, Hex Head 5/16-18 x 1-1/4 532 05 92-89 Washer, Flat 873 93 05-00 Nut, Jam, Lock 5/16-18 532 17 53-30 Pin, Idler Pivot 532 17 90-92 V-Belt, Traction Drive 810 04 05-00 Washer, Lock 5/16 817 49 05-08 Screw, Hex Head 5/16-18 x 1/2 532 17 92-59 Impeller Arm / Pad Assembly 532 08 51-79 Retainer, Hairpin 532 17 88-28 Spring, Brake 532 18 35-33 V-Belt, Impeller Drive 532 19 23-06 Screw, Hex Head 3/8-16 x 1-1/4 532 18 48-04 Arm, Idler 874 78 05-24 Screw, Hex Head 5/16-18 x 1-1/2 532 17 53-31 Bushing, Idler Pivot 532 18 05-23 Pulley, Idler (2-3/4) 874 61 05-16 Screw, Hex Head 5/16-18 x 1 532 17 93-71 Spacer, Engine Pulley 532 18 04-78 Pulley, Engine, Traction Drive 532 17 91-57 Pulley, Engine, Impeller Drive 532 06 27-35 Washer, Flat 3/8 532 85 02-63 Washer, Lock, Helical 3/8 532 85 10-84 Screw, Hex Head 3/8-24 x 1-3/8 532 15 54-52 Guide, Belt 532 19 22-13 Belt Cover Assembly (Includes Toolbox Cover) 532 17 88-30 Cover, Toolbox 817 49 04-08 Screw, Hex Head 1/4-20 x 1/2 532 17 92-56 Bolt, Shoulder 5/16-18 532 18 78-53 Bellcrank Shifter 532 18 04-01 Screw, Hex Head 1/4-28 x 3/4 532 19 57-67 Arm, Auger Control 873 80 05-00 Nut, Lock 5/16-18 532 18 40-86 Bellcrank 532 18 71-01 Link, Speed Control 532 19 21-10 Trunnion, Pivot Bracket 532 17 88-20 Nut, Cage 3/8-16 532 70 02-79 Hairpin, Cotter 3/32 x 1/2 532 17 90-65 Pin, Pivot Bracket 532 18 40-85 Bracket, Bellcrank 871 21 06-16 Screw, Hex Head 532 18 40-74 Pivot Bracket, Impeller Idler Arm 532 18 40-84 Pan, Frame Bottom 871 02 05-12 Screw, Hex Head 5/16-18 x 3/4 532 18 11-56 Nut, Speed 5/16-18 532 18 40-73 Frame Assembly 532 18 80-02 Plate, Frame End 532 19 95-14 Shaft, Auger Control 532 05 70-79 Washer, Hardened 532 19 22-75 Roller 532 19 21-47 Ring, Crescent 812 00 00-02 E-Ring 811 05 05-00 Washer, Lock, External Tooth 5/16 532 18 38-54 Power Cord NOTE: All component dimensions given in U. S. 1 inch = 25. 4 mm IMPORTANT: Use only Original Equipment Manufacturer (O. E. M. ) replacement parts. Failure to do so could be hazardous, damage your lawn mower and void your warranty. 29 REPAIR PARTS 18 10 WHEELS / DECALS 10 30 15 32 12 19 34 11 14 13 27 SNOW THROWER - MODEL NO. [. . . ]