User manual HUMMINBIRD PIRANHAMAX 170

[. . . ] PiranhaMAXTM 150, 160, 170, 180, 190c Installation and Operations Manual 531678-1_B Thank You! Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation by designing and manufacturing top-quality, thoroughly reliable marine equipment. Your Humminbird® is designed for trouble-free use in even the harshest marine environment. In the unlikely event that your Humminbird® does require repairs, we offer an exclusive Service Policy-free of charge during the first year after purchase, and available at a reasonable rate after the one-year period. [. . . ] If you have performed the preceding procedures correctly, the transducer should be level and at the right height for optimal operation. 19 Inside the Hull Transducer Installation Inside the Hull Transducer Installation In-hull mounting generally produces good results in single thickness fiberglasshulled boats. Humminbird® cannot guarantee depth performance when transmitting and receiving through the hull of the boat, since some signal loss occurs. The amount of loss depends on hull construction and thickness, as well as the installation position and process. NOTE: In-hull mounting requires an installed and operational control head. NOTE: The integral temperature probe will not work with in-hull mounting, so you may either want to consider purchasing a Temp Sensor or obtaining a different transducer. Humminbird® offers a transducer exchange program to swap the NEW and UNASSEMBLED transducer, accompanied by mounting hardware, for one without an integral temperature probe. Call the Humminbird® Customer Resource Center at 1-800-633-1468 for details, or visit www. humminbird. com for more information. This installation requires slow-cure two-part epoxy. Do not use silicone or any other soft adhesive to install the transducer, as this material reduces the sensitivity of the unit. Do not use five-minute epoxy, as it has a tendency to cure before all the air bubbles can be purged, thus reducing signal strength. 20 Inside the Hull Transducer Installation Determine the Transducer Mounting Location Decide where to install the transducer on the inside of the hull. Consider the following to find the best location: · Observe the outside of the boat hull to find the areas that are mostly free from turbulent water. Avoid ribs, strakes and other protrusions, as these create turbulence (Figure 28). · As a general rule, the faster the boat can travel, the further aft and closer to the centerline of the hull the transducer has to be located in order to remain in contact with the water at high speeds (Figure 29). Figure 28 Preferred Mounting Area Figure 29 21 Inside the Hull Transducer Installation Trial Installation You will not be able to adjust the mounting after an inside the hull transducer is installed. It is best, therefore, to perform a trial installation first that includes running the boat at various speeds, in order to determine the best mounting area before permanently mounting the transducer. Plug the transducer into the control head, then power up the control head. When the control head detects a functioning transducer, it will automatically enter Normal operating mode. View the sonar signal at its best by holding the transducer over the side, immersed in the water, so that it is pointing straight down over a known flat bottom. Use the display to benchmark against the sonar signal that will be detected once the transducer is placed in the hull. Place the transducer body face down at the identified mounting location inside the hull, with the pointed end towards the bow (Figure 28). Use a sand-filled bag or other heavy object to hold the transducer in position. The transducer cannot transmit through air, and the water purges any air from between the transducer and the hull, and fills any voids in the coarse fiberglass surface. View the sonar signal on the display and compare against what was observed in Step 2, making sure that the boat is in the same location as it was during your observations in Step 2. Otherwise, locate a new position in the hull and repeat Steps 3 through 5. Run the boat at various speeds and water depths while observing the screen on the control head. [. . . ] Any repairs made after the original warranty will be warranted for an additional 90 days after service has been performed by our factory technicians. You can contact our Customer Resource Center or visit our website to verify the flat rate repair fee for your product (visit the Product Support section): http://www. humminbird. com We reserve the right to deem any product unserviceable when replacement parts are no longer available or impossible to obtain. This applies only to Humminbird® products returned to our factory in Eufaula, Alabama. DOMESTIC (USA) CUSTOMERS: PLEASE DO NOT RETURN THIS PRODUCT TO STORE FOR SERVICE For all technical issues please call 1-800-633-1468 Or visit www. humminbird. com, click SUPPORT Please reference product serial number and model number when contacting Humminbird®. 43 Returning Your Unit for Service Before sending your unit in for repair, please contact the factory, either by phone or by email, to obtain a Repair Authorization Number for your unit. NOTE: Please do not return your Humminbird® to the store for service. Please have your product model name and serial number available before calling the factory. [. . . ]