User manual HUGHES & KETTNER ZENTERA

[. . . ] 2. 0 www. hughes-and-kettner. com BEDIENUNGSANLEITUNG ENGLISH MANUAL ZENTERA - MANUAL CONGRATULATIONS AND THANK YOU FOR CHOOSING THE ZENTERA! The zenTera® converges the most sought-after amps and effects in the history of guitar amplification in an easy-to-handle, combo-sized package. And it does it with mind-bending authenticity, delivering an audio experience you won't soon forget. TABLE OF CONTENTS 1. 0 2. 0 3. 0 3. 1 3. 2 4. 0 5. 0 5. 1 5. 2 5. 3 6. 0 6. 1 6. 2 6. 3 6. 4 6. 5 6. 6 7. 0 7. 1 7. 2 7. 3 7. 4 7. 5 7. 6 7. 7 7. 8 7. 9 7. 10 7. 11 7. 12 7. 13 7. 14 7. 15 7. 16 7. 17 7. 18 7. 19 8. 0 9. 0 10. 0 11. 0 11. 1 11. 2 11. 3 QUICK START GUIDE OR OPERATING MANUAL?. 31 The secret behind the zenTera®'s sonic sorcery is Dynamic Sector Modeling (DSMTM). We poked and probed every group of components (sectors) in the original amps and we analyzed the dynamic interaction between these sectors. [. . . ] In view of the fact that they route out signals without speaker simulation, the SEND jacks may also be used as a line out for connecting external power amps. · RETURN: Connect the output of your effects device to this jack. You can also use the RETURN jacks to connect an external signal source such as an audio playback device. However, keep in mind that in this case the zenTera®'s signal is muted, which means that if you patch in an external signal here, you can't play along with it over the zenTera®. MIDI IN/OUT/THRU: Standard MIDI trio. It also serves as the interface for loading software updates and creating preset backups. The IN port is powered via a phantom power circuit equipped with a discrete fuse. 4 1 6 2 Pin function 5 3 7 MIDI Out + (current source) n. c. MIDI Out ­ (current sink) MIDI In + (current source) MIDI In ­ (current sink) Phantom Power + (approx. 600 mA) 7: Phantom Power - 1: 2: 3: 4: 5: 6: FOOTSWITCH: Stereo jack for connecting a 1-way or 2-way sustain pedal. It lets you switch to the next higher preset number (UP) or next lower preset (DOWN) or also back and forth between two presets (TOGGLE). For the latter alternative, you have to assign a marker to one of the two presets (see 6. 5, FOOTSWITCH). Go to the system menu (see 7. 12, FOOTSWITCH ASSIGN) to select the desired UP/DOWN/TOGGLE function. Note: The zenTera® detects the polarity (1-way or 2-way) of the connected sustain pedal when it is switched on. FOOT PEDAL: Stereo jack designed to take an expression pedal such as a volume or wah-wah pedal. The volume function is the default setting unless you assigned a wah-wah effect for the given preset in PRE EFFECT MODE. (see 6. 1, PRE EFFECT MODE). 10 W: TURN KNOB r: CLICK s: DOUBLE-CLICK t: CLICK AND HOLD BRIEFLY ZENTERA - MANUAL 6. 0 SPECIAL FUNCTIONS 6. 1 PRE EFFECT MODE The following effects are available to you in this mode (see also the table INS-FX in the appendix under 11. 1). Unlike the other effects found in the effect section, the only signal routing option for these effects is PRE, in other words, in front of the input: Wah Wah: '60s vintage wah-wah Wah Wah 2: contemporary wah-wah with more bottom end Fix Wah: both wah-wahs with fixed frequency (as if you left the wah-wah pedal on in a certain position) Mod Wah: automatic version of the two wah-wahs Compressor: three compressors with different attack times - short, medium, long Tube Scream, Fuzz: two legendary distortion boxes Tap The EQ will activate and the BASS, MID, TREBLE and PRESENCE knobs are enabled. WBASS adjusts the bottom end, WMID the low mids, WTREBLE the upper mids, and WPRESENCE the top end frequencies. You can switch the EQ (tPRESET) on and off to hear how the modifications affect the sound. Once you are satisfied, leave the EQ on and exit the menu by briefly tapping rTUNER. Note: If the GLOBAL EQ was on when you switched the amp off, the amp will indicate this when you switch it on again. The idea here is of course to remind you that the EQ is still enabled. If you are in a different venue, you should switch the GLOBAL EQ off or readjust it. 6. 3 TUNER Activate the built-in tuning device by tapping rTUNER with your fingertip. A large "+" appears when the string's pitch is sharp (too high), a "-" when the pitch is flat (too low), and "OK" when the string is tuned to pitch. You can also see this indicated in the chain of lights at the bottom of the display. rAMP TYPE briefly to access PRE EFFECT MODE. In PRE EFFECT MODE, select the desired effect via WTYPE. [. . . ] TYPE FX PARA 1 PARA 2 ZENTERA-MANUAL 11. 2 MIDI IMPLEMENTATION CHART MIDI Implementation Chart v. 2. 0 (page 1 of 3) Manufacturer: Hughes & Kettner Model: Zentera Transmitted 1. Basic Information MIDI channels Note Numbers Program Change Bank Select Response?(Yes / No) If yes, list banks utilized in remarks column Modes supported: Mode 1:Omni-On, Poly (Yes/No) Mode 2:Omni-On, Mono (Yes/No) Mode 3:Omni-Off, Poly (Yes/No) Mode 4:Omni-Off, Mono (Yes/No) Multi Mode (Yes/No) Note-On Velocity (Yes/No) Note-Off Velocity (Yes/No) Channel Aftertouch (Yes/No) Poly (Key) Aftertouch (Yes/No) Pitch Bend (Yes/No) Active Sensing (Yes / No) System Reset (Yes / No) Tune Request (Yes / No) System Exclusive: Sample Dump Standard (Yes/No) Device Inquiry (Yes/No) File Dump (Yes/No) MIDI Tuning (Yes/No) Master Volume (Yes/No) Notation Information (Yes/No) Turn GM1 System On (Yes/No) Turn GM2 System On (Yes/No) Turn GM System On (Yes/No) Other (note in Remarks column) NRPNs (Yes/No) RPN 00 (Pitch Bend Sensitivity) (Yes / No) RPN 01 (Channel Fine Tune) (Yes/No) RPN 02 (Channel Coarse Tune) (Yes/No) RPN 03 (Tuning Program Select (Yes/No) RPN 04 (Tuning Bank Select) (Yes/No) RPN 05 (Modulation Depth Range) (Yes/No) 2. [. . . ]