User manual HUGHES & KETTNER ZENAMP

[. . . ] www. hughes-and-kettner. com BEDIENUNGSANLEITUNG zenAmp DYNAMIC SECTOR MODELING TM GUITAR AMP MANUAL 1. 0 ENGLISH ZENAMP-MANUAL zenAmp DYNAMIC SECTOR MODELING TM GUITAR AMP This operating manual is also available as a computer file. To download it, go to www. hughes-and-kettner. com, then to "Manuals". Hughes & Kettner, zenAmp, DSM, Dynamic Sector Modeling, Z-Board, FS-5, the Hughes & Kettner logo, the zenAmp logo, the DSM Logo, Montana, WARP 7, and ATS 112 are trademarks or registered trademarks of Hughes & Kettner. All other product names are the property of their respective owners. CONGRATULATIONS AND THANK YOU FOR CHOOSING THE ZENAMP! The findings of 20 years of research at Hughes & Kettner flowed into the zenAmp. [. . . ] The current settings of all knobs are enabled ­ what you see is what you hear. The MANUAL button also lets you switch between the sound banks of the zenAmp manually when you press and hold it down for a bit. To learn more about this, please read the next section entitled PRESETS. PRESETS 1 to 5: These knobs perform two functions: For one, they are used to call up stored user presets and factory presets. To this end, proceed as follows: 1) Activate the five presets of a sound bank by pressing the Preset buttons. 2) To switch sound banks, press and hold the MANUAL button until it starts flashing. 3) Select the sound bank by pressing one of the PRESET buttons 4) Activate the presets 1 to 5 of this bank by pressing the PRESET buttons again. Note: On the zenAmp, you can call up 30 presets - including five user presets - manually. The optionally available Z-Board increases the number of manually accessible presets to 125, 100 of which are user presets. Note also: To go from the sound banks holding the factory presets back to the five user presets, briefly press the MANUAL button. Briefly press the MANUAL button again to switch to Preset mode, which lets you access the user presets. The optional Z-Board is of course a far more convenient option for switching modes and presets. Select the desired memory slot by pressing one of the PRESET buttons 1 to 5. This overwrites the preset that was previously stored in the selected memory slot. Note: You can cancel the storage process at any time by pressing the MANUAL button. Note also: You can of course also navigate to the desired memory slot via the optional Z-Board. FX TYPE: This selector puts eight modulation effects, seven pre effects (meaning effects that plug into the front end of the amp) such as wah-wah, and a bypass at your fingertips. FX PARAMETER: Controls the parameters of the effect that you select using the FX TYPE knob. Since most of the effects offer at least two parameters, this knob actually gives you musically meaningful combinations of these parameters. When the FX PARAMETER knob is set to a low value, the chorus' rate is low, but its intensity or amount is high. As you turn the knob up, the rate increases while intensity decreases. REVERB VOL: It determines the amount of reverb that is added to the signal. The zenAmp gauges the time between taps and synchronizes the delay accordingly. [. . . ] Turn up the signal processor's output level. 12 ZENAMP-MANUAL 8. 0 APPENDIX 8. 1 MIDI IMPLEMENTATION CHART MIDI Implementation Chart v. 2. 0 (page 1 of 3) Manufacturer: Hughes & Kettner Model: ZenAmp Transmitted Recognized 1 Yes Mode 3 / 4: Omni Off Version: 1. 00 Date: 29. 03. 01/AP Remarks 1. Basic Information MIDI channels Note Numbers Program Change Bank Select Response?(Yes / No) If yes, list banks utilized in remarks column Modes supported: Mode 1:Omni-On, Poly (Yes/No) Mode 2:Omni-On, Mono (Yes/No) Mode 3:Omni-Off, Poly (Yes/No) Mode 4:Omni-Off, Mono (Yes/No) Multi Mode (Yes/No) Note-On Velocity (Yes/No) Note-Off Velocity (Yes/No) Channel Aftertouch (Yes/No) Poly (Key) Aftertouch (Yes/No) Pitch Bend (Yes/No) Active Sensing (Yes / No) System Reset (Yes / No) Tune Request (Yes / No) System Exclusive: Sample Dump Standard (Yes/No) Device Inquiry (Yes/No) File Dump (Yes/No) MIDI Tuning (Yes/No) Master Volume (Yes/No) Notation Information (Yes/No) Turn GM1 System On (Yes/No) Turn GM2 System On (Yes/No) Turn GM System On (Yes/No) Other (note in Remarks column) NRPNs (Yes/No) RPN 00 (Pitch Bend Sensitivity) (Yes / No) RPN 01 (Channel Fine Tune) (Yes/No) RPN 02 (Channel Coarse Tune) (Yes/No) RPN 03 (Tuning Program Select (Yes/No) RPN 04 (Tuning Bank Select) (Yes/No) RPN 05 (Modulation Depth Range) (Yes/No) 2. [. . . ]