User manual HUBBELL LIGHTING B-TLR

[. . . ] This symbol reminds you to read this booklet. 1 Important Information GB For your Condenser dryer to operate efficiently, you must follow the regular maintenance schedule shown below: Fluff Filter. . . !Refit the filter - NEVER run the dryer without the filter in position. !Failure to clean the filter after EVERY drying cycle will affect the drying performance of your machine. - It will take longer to dry and as a result will use more electricity during drying. Water Container. . . ! [. . . ] If you do not open the door during the 2 minute period, the dryer will resume drying without you pressing the Start/Pause button. When Cupboard Dry dryness level reached, the dryer completed the cool tumble (and, if selected, Post Care) and ends with END OF CYCLE. EMPTY WATER BOTTLE Mini Load Available with Cotton High Heat and Synthetic programmes. This programme optimises Automatic programme for smaller loads and improves the Time to End estimation. 9 Start and Programmes GB Programmes Table !If the Display is not lit; Press the ON/OFF button Programme What it does. . . Cottons High Heat and then select programme. How to set it. . . 1. - To change from default dryness setting press and release Dryness Levels button until the required level is displayed. Press the Start/Pause button . Note: Options available: Alarm , Time Delay , Pre Care , Post Care Mini Load , *Mixed Dry Dryness options: Automatic IRON DRY HANGER DRY CUPBOARD DRY : default Dries your Cotton clothes on High Heat. , Cottons Low Heat Dries your Cotton clothes on Low Heat. Dries your Synthetic clothes on High Heat. 1. Select a drying time, see Timed , next page. Options available: See Timed , next page. Synthetics Options available: button. Alarm , Time Delay , Pre Care , Post Care , - If Timed Drying , see next page, or. . . Mini Load , *Mixed Dry - To change from default dryness setting press and release Dryness Levels button Dryness options: Automatic until the required level is displayed. Press the Start/Pause button . HANGER DRY CUPBOARD DRY : default Options available: Alarm , Time Delay , Pre Care , Post Care q Bed & Bath Dries your towels and bedding on High Heat. 1. Alarm Available on all programmes and allows the buzzer to give a signal at the end of the drying cycle, to remind you that the clothes are ready to be removed. Post Care When available and selected, the clothes are occasionally tumbled after the end of the drying and cool tumble cycles, to help prevent creases developing should you not be available to remove the load immediately the programme is complete. TIME DISPLAY 88:88 The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying programme (see The Display). The delay or time to end is displayed in hours and minutes and counts down each minute. When timed programmes are selected the time displayed throughout the cycle is the actual time remaining. When an Automatic programme is selected, the time displayed is an estimate of the time remaining. When the programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller calculates a better estimate of the cycle time. The colons between the hours and minutes in the display flash to show that the time is counting down. The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault code number (see Troubleshooting). q Empty Water Container (If you have plumbed your dryer to a drain this icon can be ignored, as there is no need to empty the water container). If the water container fills during a programme, the heater turns off and the dryer does a period of Cool Tumble. After this it stops and a message tells you to EMPTY THE WATER CONTAINER . [. . . ] Release the three catches by turning 90˚ counterclockwise then pull on the grip and remove from the dryer. Clean the surface of the seals and replace, making sure that the catches have been secured. Empty the water container after each cycle Pull the container out of the dryer and empty it into a sink or other suitable drain. Always check and empty the container before you start a new drying programme. Cleaning the dryer External parts in metal or plastic and rubber parts can be cleaned with a damp cloth. q Periodically (every 6 months) vacuum the front air intake grille and vents at the rear of the dryer, to remove any build up of fluff, lint or dust. [. . . ]