User manual HOTPOINT TVF 751 X

[. . . ] 7 kg 7 kg 3 kg Cet appareil est conforme aux Directives Européennes suivantes: - 2006/95/EC (Équipement Basse Tension) - 89/336/EEC, 92/31/EEC et 93/68/EEC (Compatibilité Électromagnétique) 14 Instruction booklet TUMBLE DRYER F Français, 1 GB English, 15 Contents Important information, 16 Installation, 17-18 Where to put your dryer Ventilation Electrical connection Before you start using your dryer GB Dryer description, 19 The front The back Control panel Start and programmes, 20-22 Choosing a programme Table of programmes The controls TVF751X Laundry, 23-24 Sorting your laundry Wash care labels Special clothing items Drying times Warnings and Suggestions, 25 General safety Disposal Saving energy and respecting the environment Maintenance and Care, 26 Switching off the electricity Cleaning the filter after each cycle Check the drum after each cycle Cleaning the dryer Troubleshooting, 27 Service, 28 Spare parts !Keep this instruction booklet on hand in order to refer to it when necessary. Take it with you when you move, and should you sell this appliance or pass it on to another party, make sure that this booklet is supplied along with the dryer so that the new owner may be informed about warnings and suggestions on how the appliance works. Read these instructions carefully; the following pages contain important information on installation and suggestions on how the appliance works. [. . . ] After the Start/Pause button (Départ/Pause) has been pressed, only the Pre Creasecare (Anti-froissage Début de Cycle) and Post Creasecare (Anti-froissage Fin de Cycle) options can be changed. Time Delay (Départ Différé) The start of some programmes (see Start and Programmes) can be delayed for up to 24 hours. Press this button, the display shows OFF and the option light comes on. Press again and a 1 hour delay is selected and the display indicates 1hr, each further press of the button adds 1hr to the delay. When 24hr is displayed a further press the display shows OFF and after a couple of seconds cancels the delay. pre Creasecare (Anti-froissage Début de Cycle) This option is only available if a delayed start has been selected. It tumbles the clothes occasionally during the delayed period to help prevent creases developing. Press this button and a high heat setting is selected and the light next to the button comes on. Timed programmes have a default of low heat, if the light next to the button is on then pressing this button selects a low heat setting and the light goes out. Post Creasecare (Anti-froissage Fin de Cycle) When available and selected, the clothes are occasionally tumbled after the end of the drying and cool tumble cycles, to help prevent creases developing should you not be available to remove the load immediately the programme is complete. 22 The display shows either the amount of time delay remaining or an indication of the amount of time left for a drying programme. The time to end is displayed in hours and minutes and counts down each minute, this includes the cool tumble phase. When timed programmes are selected the time displayed throughout the cycle is the actual time remaining. When a sensing programme is selected the time displayed is an estimate of the time remaining. When the programme is selected the display shows the time required to dry a full load, after around 10 minutes the controller calculates a better estimate of the cycle time. The colons between the hours and minutes in the display flash to show that the time is counting down. When the programme finishes its cool tumble phase the display will show E88 . The display also shows if there is a problem with your dryer, if this occurs the display will show F followed by a fault code number (see Troubleshooting). Q Door Opening Opening the door (or pressing the Start/Pause button (Départ/Pause) ) during a programme will stop the dryer and have the following effects: q The Start/Pause (Départ/Pause) light flashes Amber. The Start/Pause button (Départ/Pause) must be pressed to resume the delay programme. Q During the drying part of the programme, the time to end count continues but the colons do not flash. The Start/Pause button (Départ/Pause) must be pressed to resume the programme. [. . . ] A coloured film may start to appear on the stainless steel drum, this may be caused by a combination of water and, or cleaning agents such as fabric conditioner from the wash. Cleaning q External parts in metal or plastic and rubber parts can be cleaned with a damp cloth. Periodically check the vent tube and any permanent venting fixture to make sure that there has been no accumulation of fluff or lint, and remove it. Your dryer uses special bearing components which do not need lubrication. [. . . ]